A mixture of hydrocarbon gases is composed of 60 percent methane, 25 percent propane, and 15 percent butane by weight. This mixture is compressed from 100 kPa and 20°C to 1400 kPa in a reversible, isothermal, steady-flow compressor. Calculate the work and heat transfer for this compression per unit mass of the mixture. The universal gas constant is Ry=8.314 kPa-m³/kmol-K. Use the table containing the molar mass, gas constant, and critical-point properties. P₂

A mixture of hydrocarbon gases is composed of 60 percent methane, 25 percent propane, and 15 percent butane by weight. This mixture is compressed from 100 kPa and 20°C to 1400 kPa in a reversible, isothermal, steady-flow compressor. Calculate the work and heat transfer for this compression per unit mass of the mixture. The universal gas constant is Ry=8.314 kPa-m³/kmol-K. Use the table containing the molar mass, gas constant, and critical-point properties. P₂

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the specific volume of air-vapor mixture (m3/kgda) when the following conditions prevail: t=30°C, W=0.015kg/kgda, Pt=90kPa.
CO2 needs to be compressed from p1=1bar, t1=300k to p2=40bar to transport it to remote sites for sequestration. what is the minimum energy requirement per kg of CO2 for the compressor? Should the compressor operate adiabatically or isothermally for the best energy efficiency? The environment is at Tenv=300k. Use accurate thermodynamic data for CO2 in this problem.
Question : Determine the units of the quantity s ̄/Ru, where s ̄ is the molar specific entropy and Ru is the universal gas constant. Explain your answer please
A 653 g/h stream of methyl alcohol, also called methanol, at 6.0atm 10.0C was held at constant pressure, vaporized, and brought to 241.0C. At what rate must heat, be supplied to this system ? Assume that methyl alcohol vapor behaves ideally for the temperature range and pressure given.
What is the difference between entropies of oxygen at 160 kPa and 39°C and oxygen at 160 kPa and 337°C on a per-unit-mass basis? Use the table containing the ideal gas specific heats of various common gases. The entropy difference is kJ/kg.K.
A frictionless piston-cylinder contains 42 kilograms of Acetylene having a pressure of 22 bar at 320 degrees Celsius. Heating occurs at constant pressure causing the piston to move until the volume is tripled. Compute for the (a) heat, (b) change in internal energy, (c) change in enthalpy (d) change in entropy, and (e) the non-flow work. (f) If ΔPE = 0.2 kJ and ΔKE = 1.35 kJ, what is the steady-flow work?
A 10-kg air is compressed isothermally from 1 atm and 30ºC. If 150 Btu of heat lost by the system, determine the final pressure.
A gas mixture contains hydrogen, nitrogen and carbon monoxide in equal molar proportions. Treating the components of the mixture as perfect gases, determine the gas constant and the ratio of specific heats for the mixture. Calculate the work required to compress 1 kg of the mixture in reversible adiabatic flow through a pressure ratio of 2 from an initial temperature of 15°C when kinetic and potential energy changes are negligible. [Ans. 0.43 kJ/kg K 1.4. — 82.76 kJ)
Steam at a pressure of 3.5 MPa is known to have a specific volume of 50×10*-3 m*3/kg. Find the enthalpy of the mixture ink KJ/s if the mass flow rate of the steam is 3.443 kg/s.
A 2-m3 tank initially contains a mixture of saturated-vapor steam and saturated-liquid water at 2000 kPa. Of the total mass, 25% is vapor. Saturated-liquid water at atmospheric pressure is added to the tank until the final mass is 20% more than the initial total mass of the vapor/liquid mixture in the tank. If the pressure in the tank is kept constant during theprocess, how much heat (kJ) is transferred?
Liquid water at 19.1 psig and 15°C is heated in a mixing chamber by mixing it with superheated steam at 150°C. Liquid water enters the mixing chamber at a rate of 4.3 kg/s and the chamber is estimated to lose heat to the surrounding air at 20°C at a rate of 1200 kJ/min. If the mixture is intended to leave at 80°C please answer the following. a. What should be the pressure at the inlet of the liquid water and the steam to have a good operating mixing chamber? Explain how you arrived to the value and what would happen if values for the inlet streams would be different. b. What should the pressure at the exit of the mixture be under ideal conditions? Why? c. Determine the mass flow rate of the superheated steam. d. Determine the rate of entropy generation in this mixing chamber. Could this mixing chamber operate under the given conditions? Please justify your answer with explanations. e. If the mixing chamber would have been adiabatic, is there any entropy generation? Perform a…
What is the enthalpy in kJ/kg for steam at P=1.12 MPa and T=195C?