A four-stage single-acting air compressor running in an atmospheric at 87 kPa and 15°C has a F.A.D of 2.83 m³/min. The section pressure and temperature are 80 kPa and 32 °C respectively, the delivery pressure is to be 7 MPa. The temperature at the start of compression in each stage is 32 °C, take n=1.3 for all stages. With reference to formula file the applicable formual nuber to find the intermedia pressure ratios is

A four-stage single-acting air compressor running in an atmospheric at 87 kPa and 15°C has a F.A.D of 2.83 m³/min. The section pressure and temperature are 80 kPa and 32 °C respectively, the delivery pressure is to be 7 MPa. The temperature at the start of compression in each stage is 32 °C, take n=1.3 for all stages. With reference to formula file the applicable formual nuber to find the intermedia pressure ratios is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. An air compressor is to compress 510m²/hr from 100kpa to 10bar, for an ideal compression with n=1.3, what will be the percent saving in power due to two staging?
QUESTION 26 A four-stage single-acting air compressor running in an atmospheric at 87 kPa and 15°C has a F.A.D of 2.83 m³/min. The section pressure and temperature are 80 kPa and 32 °C respectively, the delivery pressure is to be 7 MPa. The temperature at the start of compression in each stage is 32 °C, take n=1.3 for all stages. With reference to formula file the applicable formual nuber to find the intermedia pressure is The intermidiate pressure ratio is (to 3 decimal places), The intermidiate pressure at first, second and third stage in kPa to 1 decimal place are: and respectively. No need to add units
QUESTION 27 A four-stage single-acting air compressor running in an atmospheric at 87 kPa and 15°C has a F.A.D of 2.83 m³/min. The section pressure and temperature are 80 kPa and 32 °C respectively, the delivery pressure is to be 7 MPa. The temperature at the start of compression in each stage is 32 °C, take n=1.3 for all stages. With reference to formula file the applicable formual number to find the mass flow rate and power input is and , respectively. The mass flow rate to 3 decimal places in kg/min and power input in kW to 1 decimal place are: , and , respectively. No need to add units
Read the question carefully before answering. Box or indicate your final ansurers when solving and draw your diagrams cleanly. Complete solution please. Use 2 decimal places when solving and for final answers. Draw the PV and TS diagram with proper label of points when required. 5. A centrifugal compressor has a single stage and 4 stage model with suction conditions of 100 kPa and 25c. The air must be discharged at 300 kPa. Find the compressor work and heat rejected for each model if the compression is isentropic, and the intercooler pressures.
no. 3 question: A diesel engine powers a boat. The engine’s cylinders each have a compression ratio (Vmax/Vmin) of 12 and the Vmax is 4ft3. If 1 cylinderis in the isobaric compression stroke, find the final temperature if the initial temperature is 540F Main question: From number 3, if the gas tankaccident happened on top of Mt. Everest’s summit where patm is only 33.7 kpa and the readings obtained are the same, find the new finaltemperature
Which is more efficient, dry or wet standardammonia vapor compression system in such away it is dry after compression. Justify answerby computation.
The compression ratio of an Otto cycle is 8, at the beginning of the zanthropic compression process, the pressure of the air is 100 kPa, the temperature is 27 "C, the volume is 550 cm. At the end of the lzantropic expansion process, the temperature of the air is 700 K. Using the specific temperature values at room temperature (according to the cold air standard assumptions) Find the gravity of the air.
b- An evacuated tank ,shown if fig of 1 ft3 is coupled to air supply line through valve .When the valve is opened, the air flow from supply line at 70°F,120 psi until the pressure reaches 90psi . calculate the final temperature and mass inside tank ,assuming the process is adiabatic. R= 53.34 Ibf-ft/lbm °R use the table below in case. Alr supply line Tank Idcat-Gas Propertiles of Air (English Units)0, Standard Entropy at 1 atm = 161.325 kPa = 14.696 1bf/in.² (R) (Btulbm) (Btu/lbm) (Btu/lbm R) (R) (Btu/lbm) (Btu/lbm) (Btu/Ibm R) 400 68.212 95.634 1.56788 1950 357.243 490.928 1.96404 440 75.047 105.212 1.59071 2000 367.642 504.755 1.97104 480 81.887 114.794 1.61155 2050 378.096 S18.636 1.97790 520 88.733 124.383 1.63074 2100 388.602 532.570 1.98461 536.67 91.589 128.381 1.63831 2150 399.158 546.554 1.99119 540 92.160 129.180 1.63979 2200 409.764 560.588 1.99765 560 95.589 133.980 1.61852 2300 431.114 588.793 2.01018 600 102.457 143.590 1.66510 2400 452.640 617.175 2.02226 1000 172.564…
Provide the diagram, given, and ste by step solution. An air standard engine has a compression ratio of 15 and a cut off ratio of 3. If theintake air pressure and temperature are 100 kpa and 28 degree Celcisus, find the work in KJ per kg.
Q1. A vapour compression refrigeration uses R-12 as a refrigerant and the liquid evaporates in the evaporator at - 15°C. The temperature of this refrigerant at the delivery from the compressor is 15°C when the vapour is condensed at 10°C. Find the C.O.P. if (i) there is no under cooling (ii) the liquid is cooled by 5°C before expansion by throttling. Take specific heat at constant pressure for the superheated vapour as 0.64KJ/kg k. and that for liquid as 0.94KJ/kg k the other properties of refrigerant are as follow: a) Temperature b) 0°С с) Enthalpy(KЈK)) d) Entropy(KJ/kg k) e) liquid _j) 22.3 0) 45.4 f) Vapour k) 180.88 g) liquid 1) 0.0904 9) 0.1750 h) Vapour m) 0.7051 i) -15 n) 10 p) 191.76 r) 0.6921
mbustion. 4G* UE E I 62% 1:29 ... Question 2 2.1 A single stage double acting air compressor of 150KW power takes air in at 16 bar & delivers at 6 bar. The compression follows the law PV1.35 = C. the compressor runs at 160rpm with average piston speed of 150 m/min. Determine the size of the cylinder.
Draw the layout of gas turbine plant which has two stage of compression with perfect inter-cooling. The high pressure turbine develops power enough only to drive the high pressure compressor. The low pressure turbine derives both the L.P compressor and load. Show the ideal process of this plant on T-S diagram.