A double tee cross section is used for the beam shown below. Assume the following lengths and loads: a = 14 ft b = 7 ft c = 9 ft P = 8000 lb Q = 3000 lb The moment of inertia of the cross section is l₂ = 110 in.4. Determine the magnitude (i.e., the absolute value) of the maximum tensile bending stress in the beam. a ๆ B b C X y ↑ 3.2 in. TT 5.8 in.

A double tee cross section is used for the beam shown below. Assume the following lengths and loads: a = 14 ft b = 7 ft c = 9 ft P = 8000 lb Q = 3000 lb The moment of inertia of the cross section is l₂ = 110 in.4. Determine the magnitude (i.e., the absolute value) of the maximum tensile bending stress in the beam. a ๆ B b C X y ↑ 3.2 in. TT 5.8 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C P Steel: A=900 mm² E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the value of P without exceeding the allowable stress of bronze, in kN? 174 145 161 124
Practice 2 A fixed ended steel beam 8m long carries a uniform load 20kN/m and an axial tensile force of 200KN. The properties of steel section is as follows: A = 7800 mm? d = 324 mm Ix = 140x10 mm ly = 16x10 mmt What is the axial stress of the beam, in MPa. What is the actual bending stress in the beam due to uniform load alone acting on the beam, in MPa. -. What is the interaction value if Fb = 210 MPa and Ft = 100 MPa? answer key а.)25.64 Мра b.) 123.43 Мра c.) 0.844
A steel cantilever beam is fabricated from two structural tees welded together, as shown in the figure. For this beam, the allowable bending stress is 150 MPa, the allowable shear stress of the steel is 100 MPa, and the allowable shear flow along the weld is 2MN/m. Determine the allowable force P that the beam can carry. (All dimensions are in mm).
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b= 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 u is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load p?
A small aluminum alloy [E = 73 GPa] teeshape is used as a simply supported beam as shown. For this beam, a = 150 mm. The cross- sectional dimensions of the teeshape are b = 25 mm, d= 38 mm, and t=7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 490cis measured from a strain gage located at c= 9 rmm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d a a H Answer: P = i
Determine the maximum compressive and tensile bending stresses of the beam shown, cross-section of the beam is given below
A small aluminum alloy [E = 71 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 120 mm. The cross- sectional dimensions of the tee shape are b = 17 mm, d = 26 mm, andt = 6 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P P ЗР Strain gage C |D H Answer: P = N
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. a b C Steel: A-900 mm E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? 0.367 0.433 0.467 0.333
Compute for the maximum allowable distributed load o that can be applied to the simply supported beam as shown in Figure M-Va. The beam's cross section is detailed in Figure M-Vb. @(N/m) Allowable Stresses: Fiber Stress = +13.5 MPa / -12 MPa Transverse Shear Stress at NA = 900 kPa Transverse Shear Stress at Junction 800 2 m Figure M-Va 2 m Draw the flexural and shear stress distributions of the cross section. T 40 40 40 Figure M-Vb 40 120 mm
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage D E H b. Answer: P = i 29254 N
X Your answer is incorrect. A small aluminum alloy [E = 75 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b = 21 mm, d= 32 mm, and t = 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 7 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d D E 2 H b Answer: P = i 112.79 N %3D