A DC shunt generator has a full load output of 10kW at a terminal voltage of 240V. The armature and the shunt field winding resistances are 0.6 and 160 ohms respectively. The sum of the mechanical and core-losses is 500W. calculate the power required in kW at the driving shaft at full-load, and the corresponding efficiency and voltage regulation.

A DC shunt generator has a full load output of 10kW at a terminal voltage of 240V. The armature and the shunt field winding resistances are 0.6 and 160 ohms respectively. The sum of the mechanical and core-losses is 500W. calculate the power required in kW at the driving shaft at full-load, and the corresponding efficiency and voltage regulation.

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter37: Motor Installation

Section: Chapter Questions

Problem 9RQ

See similar textbooks

Similar questions

A long-shunt compound-wound generator gives 240 volts at F.L. output of 100A. The resistances of various windings of the machine are : armature (including brush contact) 0.1 Q, series field 0.02 Q, inter pole field 0.025 2, shunt field (including regulating 0.2 resistance) 100 2. The iron loss at F.L. is 1000 W; windage and friction losses total 500 W. Calculate F.L. efficiency of the machine.
A 4-pole shunt generator with wave-wound armature has 41 slots, each having 12 conductors. The armature resistance is 0.05 ohms and shunt field resistance s 200 ohms. The flux per pole is 25 mWb, if a load resistance of 10 ohms is connected across the armature terminals, calculate the voltage across the load when generator is driven at 1000 rpm
B. A compound generator delivers 140 A at 300 V and the resistance of the shunt field, series field,and armature are 30 52, 0.2 52, and 0.1 S2 respectively. Calculate the electromotive force
An 8 pole, lap connected armature has 500 conductors and its generated e.m.f is 120V. If the flux per pole is 20 mWb, then the speed of machine is,
A dc shunt generator delivers 125 A load current at 250V. Estimate the emf induced if the armature resistance is 0.05 ohm and shunt field resistance is 50 ohms.
A balanced star-connected load of (8 + j6) Q per phase is connected to a Balanced 3- phase 400-V supply. Find the line current, power factor, power
Q1/ B/ A shunt DC generator delivers 450A at 230V, and the resistances of the shunt and armature windings are 50 and 0.03 ohm, respectively. .Calculate the generated EMF
Example 7-3. A 460-V, 25-hp. 60-Hz, four-pole, Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: - 0.641n X,-1.106 N R2 - 0.332 N X2 = 0.464 XM - 26.3 N The total rotational losses are 1100 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.2 percent at the rated voltage and rated frequency, find the motor's (a) Speed (b) Stator current (c) Povwer factor (d) Peony and Pout (e) Tiad and Toad Efficiency
Q3:A: (a) A 10-hp 230-volt shunt-wound motor has rated speed of 1000 rpm and full-load efficiency of 86 percent. Armature-circuit resistance, 0.26 ohm; field-circuit resistance, 225-ohms. If this motor is operating under rated load and the field flux is very quickly reduced to 50 percent of its normal value, what will be the effect upon back emf, armature current and torque? What effect will this change have upon the operation of the motor, and what will be its speed when stable operating conditions have been regained?
A long – shunt compound generator delivers a load current of 50A at 500V and has armature, series field and shunt fields resistance of 0.05 ohms, 0.03 ohms and 250 ohms respectively. Calculate the generated voltage and the armature current. Allow 2 V brush contact drop.
The following data were obtained on a 50 kVA 2400/120 V transformer: Open circuit test, instruments on low voltage side: Waltmeter reading = 396 Watts Ammeter reading = 9.65 amperes Voltmeter reading = 120 Volts Short circuit test, instruments on high voltage side: Waltmeter reading = 810 Watts Ammeter reading = 20.8 amperes Voltmeter reading = 92 Volts Find the efficiency when rated kVA is delivered to a load having a power factor of 0.8 lagging.The following data were obtained on a 50 kVA 2400/120 V transformer : Open circuit test, instruments on low voltage side: Waltmeter reading = 396 Watts Ammeter reading = 9.65 amperes Voltmeter reading = 120 Volts Short circuit test, instruments on high voltage side: Waltmeter reading = 810 Watts Ammeter reading = 20.8 amperes Voltmeter reading = 92 Volts Find the efficiency when rated kVA is delivered to a load having a power factor of 0.8 lagging.
5:33 PM What is the largest power 10/10 that can be transmitted by the pulley A of a V-belt drive. Illustrated below. Given: n1 = 3000.rpm, r1 = 80 mm, ß =18°, ¤=160°, f = 0.25, F= 1100 N, w = 1.4 N/m. F2 15.7Nm , 4.93 kW 14.6Nm, 5.07kW 13.2Nm, 6.09kW 12.5Nm, 5.34kW Other: