A bimetallic strip (brass/steel), which is straight at room temperature, will be immersed in boiling water and allowed to equilibrate. I will then remove the strip and quickly place it on a piece of graph paper to measure the deflection of the end, ie. how far the end is away from the original line, measured perpendicular to the original line. Predict how far the end will deflect, to the nearest half millimeter. The bimetallic strip is 222 mm long. I measured the thickness to be 0.036". You may inspect the room- temperature strip and check my measurements.

A bimetallic strip (brass/steel), which is straight at room temperature, will be immersed in boiling water and allowed to equilibrate. I will then remove the strip and quickly place it on a piece of graph paper to measure the deflection of the end, ie. how far the end is away from the original line, measured perpendicular to the original line. Predict how far the end will deflect, to the nearest half millimeter. The bimetallic strip is 222 mm long. I measured the thickness to be 0.036". You may inspect the room- temperature strip and check my measurements.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The theoretical failure strength is significantly higher than the empirical failure strength of polycrystalline materials, even when they are highly polished because: a) Polycrystalline materials have little or no capacity for plastic deformation, so they have lower failure stresses b) Plastic deformation in polycrystalline materials adsorbs energy which reduces their failure strength c)The energy needed to break the atomic bonds in crystal lattices is lower in polycrystalline materials as compared to in single crystals d)Polycrystalline materials contain internal discontinuities
Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first graph should show engineering stress vs engineering strain, and the second graph should show true stress vs true strain. Label the showing: (i) elastic modulus (ii) proportional limit (iii) yield stress (iv)yield strain (v) fracture stress (vi) fracture strain on each graph. You may showboth graphs on one plot. Explain the difference between engineering stress and true stress.
!A tension test performed on a metal specimen to fracture produced the stress- strain relationship shown in Figure Pi.14. Graphically determine the following (show units and all work): a. Modulus of elasticity within the linear portion. b. Yield stress at an offset strain of 0.002 m/m. c. Yield stress at an extension strain of 0.005 m/m. d. Secant modulus at a stress of 525 MPa. e. Tangent modulus at a stress of 525 MPa. 750 600 450 300 150 0.002 0.004 0.006 0.008 0.01 0.012 Strain, m/m FIGURE P1.14 Stress, MPa
A part has been designed and its dimensions cannot be changed. To minimize its deflections under the same loading in all directions irrespective of stress levels, which material would you choose: Steel Aluminum Titanium Stainless Steel
Using the figure from Question 2, imagine the lamp gets heavier and heavier until one of the cables breaks. If all of the cables have the same tensile strength, a) which one will break first, and b) why will that one specifically break first? You do not need to provide Given, Assume, and Problem Type/Features for this question. You just need to provide Find, Analyses and a Conclusion. Provide an explanation for b) that isclear, concise, correct and well organized. Use at least one diagram (2D or 3D) to make your case as to why one of them will break before the others. You can use equations/math to support your explanation as well, if you want, but expressing your answer in words and using logic will be all that is necessary. Youranswer to a) i.e. which one will break first, can be your “Conclusion” to Question 3
The graph below shows the yield stress for a polycrystalline metal as a function of the grain size of the metal. The point A is (10 microns, 100 MPa) and B is (1000 microns, 28 MPa). Using this data, calculate what is the closest numerical match to the yield stress at 2 microns. yield stress (MPa) 8 8 8 8 8 8 8 80 70 50 40 30 A 200 Select one: O a. 198.9 MPa O b. 310.9 MPa O C. O d. 80.5 MPa 252.6 MPa O e. 165.2 MPa 400 600 grain size d (microns) 800 B ● 1000
In the First project: you have been asked to perform tensile testing for four different materialsand analyse the results and work on some NDT process selection:a. For the results shown in Table 1 of the tensile testing that you have performed, find thefollowing, if you know that the original length of specimen is 20.8 mm and the original diameteris 6.4 mm. Fill the calculated results in the summary table below (Table 1):1. Plot the engineering stress versus engineering strain for each material and L-D Diagram.2. Compute the modulus of elasticity, E in GPa.3. Determine the yield strength at a strain offset of 0.002.4. Determine the tensile strength in MPa.5. What is the approximate %El ductility, measured by percent elongation?6. Compute the modulus of resilience.7. Determine the fracture stress in MPa.8. Compute the final area (Af) in mm2.
a) List any four experimental methods to find the stress concentration factor. b) Explain how stress concentration can be reduced when a notch is unavoidable in a mechanical component with neat sketches?
b) Derive the general finite element equations for a solid structure. Hint: The functional for stress analysis of deformed solid structures is "Potential energy".
) What is thermal expansion stress, give equation for thermal deflection with temperature. ii) Most materials expand on heating, name there a material that contracts on heating. iii) Give 1 or more useful application of thermal expansion deflection and 1 or more harmful effect of the same that engineers have to consider in their design.
Q1. Imagine you are working for an automotive manufacturer and are selecting plastic materials for various components. Draw the structure of a material you might use for a soft touch plastic. Now draw the structure of a material you might use in the drive train (i.e., an engineering plastic). What characteristics are you engineering into the material? Q2. Based on what you know about the calorimetry of melting and crystallization, do you expect melting to be endothermic or exothermic? What about condensation? Can we say anything general about heat flow in the process of forming bonds, covalent or van der Waals?
Please clearly write out the entire process (stiffness matrix method) thank you.