Answered: A beam is loaded as shown in the…

A beam is loaded as shown in the figure. What is the equivalent concentrated load on the beam? ... 50 Ibsin 20 bsin 36 in R2 |R1 A) 500 Ibs B) 540 Ibs 1260 Ibs D) 1000 Ibs

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A high strength steel with modulus of elasticity of A N/mm', yield strength of B N/mm and crushing strength of C N/mm2 is used for a test. In the instance of crushing total strain was measured as D a) Find the ductility of steel. b) What should be the diameter of the bar to carry a load of E kN without any plastic deformation. A B D E 249000 1420 1660 2.90% 59
i need clear ans and solve very very fast in 20 min and thank you DYBALA -8 Discuss the stability and determinacy of the structures shown in Figure (1). m (a) Frame th (c) Frame ifth (d) Composite Figure (1) (b) Truss क (e) Beam
A 6m long solid bar of circle section has 140mm diameter for aluminum for length of 4m, while it has 120mm diameter for a length of 2m for steel bar, as shown in figure. Find the elongation of the bar, when it is subjected to an axial tensile force of 300 kN. Take Est-200GPa, Eat 70 GPa. (20 140 I 300 Kn Aluminum 4 m Steel 2 m 300 Kn 120
2- the rubber blocks shown in Figure 2 are used in a double U shear mount component. The dimensions of the rubber blocks are 15 x 21 x 25 mm and the applied load of 650 N cause the upper frame to be deflected by 5 mm. ↓ Double U anti-vibration shear mount 15 Shear deformation of blocks 25 Rubber block dimensions 21 오 Figure 2 (a) determine the average shear stress and shear strain in each of rubber blocks (b) determine the shear modulus G of the rubber material used in this component.
A mountain bike manufacturer is considering a new product line that will include handlebarextenders applied to the ends of the handlebars, as shown below. To validate this design change,you have been tasked with analysing the structure. You have produced an idealised structure, shownbelow, where you consider half the length of the handlebars with a fixed boundary condition (A)applied to the plane of symmetry. You have estimated that the maximum load that a rider can applyto one handlebar extension is 75 Newtons that acts 100 mm from the centreline of the handlebars.The handlebars have a circular cross-section with an outer diameter of 32 mm and a wall thicknessof 3.25 mm. P1 is the critical point. If the maximum permissible tensile stress is 150 MPa and themaximum permissible in-plane shear stress is 55 MPa, what is the largest load, P, that can beapplied by the rider? Justify your answer.
A mountain bike manufacturer is considering a new product line that will include handlebarextenders applied to the ends of the handlebars, as shown below. To validate this design change,you have been tasked with analysing the structure. You have produced an idealised structure, shownbelow, where you consider half the length of the handlebars with a fixed boundary condition (A)applied to the plane of symmetry. You have estimated that the maximum load that a rider can applyto one handlebar extension is 75 Newtons that acts 100 mm from the centreline of the handlebars.The handlebars have a circular cross-section with an outer diameter of 32 mm and a wall thicknessof 3.25 mm.To assess the design, you will: state of stress at all points (P1, P2, P3 and P4) adjacent to the fixed support. These points are located on the exterior surface of the handlebars. Present your results in a table and ensure that your sign convention is clearly shown (andapplied consistently!)
Q.1 A T-bean has the dimensions as shown below. If it is made of an elastic perfectly plastic material having a tensile and compressive yield stress 250MPa, determine the plastic moment that can be resisted by the beam 15mm 100mm 120mm 15mm
A cantilever beam with a 'T' shaped cross-section is loaded with a distributed load as shown below. The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm. A y Parameter L a d 0 L B 777 Description Beam length T Width of the flange Height of the web Yield stress |←0 →| Value 250 80 75 250 y Units mm mm mm MPa You are tasked with ensuring the beam can withstand the applied loading. To do this you must: a) Calculate the centroid for the given cross-section. Your value of y should be measured from the bottom of the section. Determine an expression for Q (statical moment of area) for the given shape. The expression(s) for Q should be in terms of the variable, y, measured from the bottom of the section.
Complete Table P4.2. For a member where a deflection criterion controls, which material would require a larger cross section? What about for a member where tension controls? TABLE P4.2 Mild Steel 7178 T76 Aluminum Yield Strength Ultimate Strength Modulus of Elasticity
0/10 FIND DEFLECTION IN Aluminum. IF E st= .200000 MPa, Ealu.=70000 MPa 100 kN R ALU.=30 MM Aluminum Steel 0.4 mm 2 mm 0.5 mm 0.25 mm no one 1m_ RST = 20 MM
(40 How A Rismatic steel bar of a Square cro ss section (looxlo0)mm is loaoled by Compressive force P= 1300 K, the bar has length 2.5 m, Eg=200GPay V=0.3,determine the shortening 8, the increase in the dimensions of cross Section, the change in Volume DV of the bar? loomm loomm
The assembly shown in Figure No. 3 consists of a hollow steel [E = 200 GPa] tube (1) with an outside diameter of 60 mm and a wall thickness of 5 mm, a solid 40 mm diameter aluminum [E= 70 GPa rod (2), and a solid 30 mm diameter aluminum rod (3). The member lengths are L1 2 000 mm, L2 = 1 200 mm, and L3 %D 3D800 mm. The following loads act on the assembly: P = 150 kN, Q = 80 kN, and R = 115 kN. Determine (a) the change in length of steel tube (1). (b) the deflection of joint D with respect to the fixed support at A.