i need clear ans and solve very very fast in 20 min and thank you DYBALA 8 Discuss the stability and determinacy of the structures shown in Figure (1). m (a) Frame (c) Frame 杰 (d) Composite Figure (1) (b) Truss क (e) Beam

i need clear ans and solve very very fast in 20 min and thank you DYBALA 8 Discuss the stability and determinacy of the structures shown in Figure (1). m (a) Frame (c) Frame 杰 (d) Composite Figure (1) (b) Truss क (e) Beam

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 6.1 A set of dual tires is spaced at 34 in. center to center and carries a total load of 45,000 lb…

A: S = 34 in p = 100 psi z = 25 in

Q: Problem (A) Find the thickness of metal necessary for a cylindrical shell of internal diameter 160…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: 2. If biodegradable organic matter, oxygen, and microorganisms are placed in a closed bottle, the…

Q: A 20 kN/m 3 m 1.5 m 20 KN 15 kNm 1.5 m B

A: Young's Modulus is 200kN/mm2

Q: Statement (1): The trap efficiency of a reservoir increases with age as the reservoir capacity is…

Q: A cantilever is carrying a triangular load as shown. Find the moment M at the fixed end when length…

A: Given data in question Load 10 kN/mSpan 0.7 mTo find out Moment at fixed end

Q: A single span beam which carries a uniform load of 30kN/m has an unsupported span of 5m. It is made…

A: Uniform loadUnsupported spanCompressive load at centroidWooden sectionAllowable stresses (80% stress…

Q: The various approximations approaches described in this section can be used to compare K_a for both…

Q: What is the value of the shear stress at the neutral axis in a rectangular section of base b, height…

Q: The gate entrance to a park opens at 9:00 A.M. At 9:00 A.M. there are 32 vehicles in the queue…

Q: D) If the diameter of the cross-section of the beam is 500 mm compute for the maxumum shearing…

A: A simply supported beam of span 10m is loaded with a UDL of 50 kN/m on the whole span and 50 kN at…

Q: A steel bar of diameter d = 31 mm and length L = 279 mm when loaded axially by a compressive force…

A: Diameter, d= 31 mnLength, L= 279 mmdx= 0.2 mmdy=? E= 200 KN/mm2 Poisson's ratio, v = 0.3

Q: ressure in gravity dams: . A drainage gallery reduces the uplift pressur at all levels below the…

Q: 230 mm Compute for the moment of inertia of the square hollow tube 250 mm

Q: A combined footing is proposed to support two columns, C1 and C2, with loads equal to 2000 kN and…

A: (i) Soil Bearing Capacity:The bearing capacity of the soil can be calculated using the following…

Q: For the inverse T-section beam that loaded as shown in figure, find the maximum tensile and…

A: A double overhanging beam is given we need to find out maximum tensile and compressive bending…

Q: Analyze the continuous beam on the photo. Please show how to draw the shear, moment diagrams and the…

A: To Anayse the beam and to draw the shear and moment diagram.

Q: nsider the following statements relat essure in gravity dams: A drainage gallery reduces the uplif…

Q: essure in gravity dams: A drainage gallery reduces the uplift pressure at all levels below the…

Q: The opposite figure has a triangular part of density ρ1=8.5 kg/m2, and a quadrant of ρ2=17 kg/m2.…

A: Given data in question Triangle with base and height 8.8 and 6.9 mQuarter circle of radius 6.9…

Q: From the load diagram below determine the following 2.5 m 30 kN/m B 0.5m 10 kN/m Shear and moments…

A: A simply supported beam with uniformly varying load and uniformly distributed load.To find:…

Q: Determine the axial forces, shears and bending moments at points A and B of the beams shown. a) 90…

Q: The following results were obtained at failure in a series of drained triaxial tests on fully…

A: 38 mm diameter by 76 mm long specimen. All-round pressure (kN/m2)= 200 400…

Q: Consider the following statements related to uplift pressure in gravity dams: 1. A drainage gallery…

Q: 6.24. In Problem 6.6, what is the maximum downwind distance at which the ground level con-…

A: Wind speed (V)= 3 m/s Stability class CEmisson rate (Q) = 1000 g/s Ground level concentration (C)=…

Q: essure in gravity dams: A drainage gallery reduces the uplift pressure at all levels below the…

Q: Determine the internal force of all members if load P = 182 kN and load Q = 175 kN. NOTE: Positive…

Q: A double-inlet grating's capacity To drain a paved apron area, a double-inlet grating similar to the…

Q: diameter Given: metal specimen x-section (circular) = D.55 in. Gage length = 2.030 in. Fracture…

A: Initial diameter, Initial length, Failure load, Final length, Final diameter, To find: (a) Ultimate…

Q: B/ For the frame shown in Figure (1-B), draw axil force, shear force, and bending moment diagrams.…

A: Draw the axial force, shear force and bending moment diagram of the frame.

Q: Q4: The structure in fig determine the components of the pin reaction at D on member (ACD). cable…

Q: (a) The detached servant room of a quarter is having internal size of 3.0m x4.50m. It is to be…

Q: A Fink truss is loaded as shown, calculate the forces in members BD, CD and CE. Assuming the members…

Q: A treatment plant has been designed to achieve 99 percent inactivation of Giardia Lamblia using…

A: 99% disinfection Present temperature = 20oCNew temperature = 0.5oC

Q: onsider the following statements related to uplift ressure in gravity dams: A drainage gallery…

Q: Tollowing pressure in gravity dams: 1. A drainage gallery reduces the uplift pr at all levels below…

Q: A layer of sand, 4m thick, overlies a layer of low permeability clay, 5m thick. The bulk unit weight…

A: Bulk unit weight of sand = 16.5 KN/m3saturated unit weight of sand = 18 kN/m

Q: onsider the following statements related to essure in gravity dams: A drainage gallery reduces the…

Q: (c) A thin, triangular plate ABC is uniformly deformed into a shape ABC', as shown by the dashed…

Q: 19 mm 19 mm 190 mm -11 mm 410 mm A) Moment of inertia along x - axis B) Static moment at N.A

A: Symmetrical I-section.To find: (a) Moment of inertia about x-axis. (b) Static…

Q: Thermal Loading Calculation: Roof Cooling Load A 56 ft. by 82 ft. roof on a building in Miami, FL is…

A: Size of roof thickness of lightweight concrete used inside air temperature

Q: (7) Water flows in a rectangular channel with base width B-5 m and depth D=1.5 m. It then flows…

A: Given data Initial and final depth 1.5 and 0.5 mWidths 5 m find out Discharge Force

Q: 3.11 An earth embankment is to be compacted to a density of 120.9 lb/ft³ at a moisture content of 14…

Q: 1. Assuming that the President Street Municipal Wastewater Treatment Plant (MWTP) processes on…

A: Organic carbon loadingSavannah River flow

Q: Classify the structures for Stability and determinacy , if unstable state why, if indeterminate…

Q: An existing equal-tangent sag vertical curve is designed for 60 mi/h. The initial grade is −3% and…

Q: Statement (1): The trap efficiency of a reservoir increases with age as the reservoir capacity is…

A: This question is related to Dams and spillways from Irrigation engineering from Civil Engineering.…

Q: 1. Identify then differentiate the ff Cast Iron Wrought Iron Iron ore Metal Steel Principles of…

A: Identify them differentiate the followings: Cast IronWrought IronIron Ore MetalSteel

Q: 49. A 32 It simple span simple span beam of 2.4 k/ft plus its self-weight and a unifo 3.0 k/ft. The…

Q: A B | L→ L→→ 60° wwwwww G F H D 50 kN 50 kN 50 KN E For the truss shown in the above figure, the…

Question

i need clear ans and solve very very
fast in 20 min and thank you
DYBALA
-8
Discuss the stability and determinacy of the structures shown in Figure (1).
m
(a) Frame
th
(c) Frame
ifth
(d) Composite
Figure (1)
(b) Truss
क
(e) Beam

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: State of given data

VIEW

Step 2: Calculation of static Indeterminacy of frame

VIEW

Step 3: Calculation of static Indeterminacy of truss

VIEW

Step 4: Calculation of static Indeterminacy of frame

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Steel 1 m Aluminum T 0.75 m Determine the maximum permissible value of T subject to the following conditions: tt S 80 MPa, Tal 50 MPa, and the angle of rotation of the free end is limited to 0.1 radian. For T. Hollow Solid d= 30 mm D= 40 mm %3D steel, G = 82 GPa and for aluminum, G= 28 GPa. %3D d = 30 mm %3D
The equation of deformation is derived to be y = x³ - xL for a beam shown in the figure. YA The curvature of the beam at the mid-span
Truss Analysis (Statics of Rigid Bodies)
The static indeterminacy of the structure shown below is Hinge - K I J H F E G A B D
A 260 mm bar AB with a rectangular cross section of 17 x 30 mm, consists of two aluminium layers with cach being 6 mm thick and brazed to a centre steel layer of 5 mm thickness as shown in Figure Q3. An axial tensile force of P- 37 kN is applied to the assembly by means of a rigid end cap at B. Given that the assembly is fixed at end A and the Young's modulus of aluminium and steel are E.= 70 GPa, Es= 200 GPa, respectively, determine: i Whether this structural configuration is statically determinate or statically indeterminate, and clearly explain your reasoning. ii. The normal forces in the aluminium layers and the steel layer i. The normal stress in the aluminium layers and the steel layer. State whether the stresses are in tension or compression iv. Determine the deformation of the assembly Cross section of the bar 6 mm 5 mm 6 mm 30 mm 260 mun Aluminium. Steel- Aluminitum Nא 37 30 mm
A high-strength bolt that passes through a steel plate is subjected to a tension force of P as shown in the figure. The hole in the metal plate has a diameter of D=17 mm which is slightly larger than the diameter of the bolt (d, = 12 mm) to allow for easy installation process. The plate has a thickness of t= 9 mm. The bolt head has a thickness of a = 9 mm and an outer diameter of dn = 24 mm. %3D Determine: A) the maximum value of P before the shear stress in the rod head exceeds Thot = 105 MPa. B) the maximum value of P before the punching shear stress in the support plate exceeds Tplate = 75 MPa. C) the maximum value of P before the bearing stress between the rod head and the support plate exceeds aplate = 110 %3D MPa. D) the maximum value of Pmax that can be supported by the structure.
An open-link chain is obtained by bending low-carbon steel rods of 0.5-in. diameter into the shape shown (Fig. a). Knowing that the chain carries a load of 160 lb, determine (a) the largest tensile and compressive stresses in the straight portion of a link, (b) the distance between the centroidal and the neutral axis of a cross section. 160 lb 160 lb -0.5 in. 0.65 in.
Explain the following assumptions used in the theory of simple bendinga) The plane section of a beam remains plane after bendingb) The material in the beam is homogeneous
In the figure shown, the AB part of the rod is made from brass while the BC part is fabricated from aluminium, both parts are restrained at the ends. Find: 1) The normal stresses oAB and OBC + when the temperature is increased to 42°C. 2) The deflection at point B (SB) Brass: ab=20.9*10-6 1/°C, Eb=105GPA Aluminum: aal=23.9*10-6 1/°C, Eal=72GPA 60 mm diameter A 1.1 m B 40 mm diameter 1.3 m C Aluminum Brass
PLEASE SCAN OR ANSWER LEGIBLY THANK YOU (STRAIN/STRENGTH OF MATERIALS)
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
In the figure shown, the AB part of the rod is made from brass while the BC part is fabricated from aluminium, both parts are restrained at the ends. Find: 1) The normal stresses oAB and OBC + when the temperature is increased to 42°C. 2) The deflection at point B (8B) Brass: a,=20.9*10-6 1/°C, Eb=105GPA Aluminum: aal=23.9*10-6 1/°C, Eal=72GPA 60 mm diameter A 1.1 m В 40 mm diameter 1.3 m C Aluminum Brass