The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure stress for the steel is (oraila = 350 MPa, determine the minimum thicknesst of the pipe if it supports the force of 500 kN. Use a factor of safety against failure of 1.5. Also, find the minimum radius r of the base plate so that the minimum factor of safety against failure of the concrete due to bearing is 2.5. The failure bearing stress for concrete is (a)oon = 25 MPa. s00 kN 100 mm

The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure stress for the steel is (oraila = 350 MPa, determine the minimum thicknesst of the pipe if it supports the force of 500 kN. Use a factor of safety against failure of 1.5. Also, find the minimum radius r of the base plate so that the minimum factor of safety against failure of the concrete due to bearing is 2.5. The failure bearing stress for concrete is (a)oon = 25 MPa. s00 kN 100 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Mechanics of Deformable bodies The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure stress for the steel is (sfail)st = 350 MPa, determine the minimum thickness t of the pipe if it supports the force of 500 kN. Use a factor of safety against failure of 1.5. Also, find the minimum radius r of the base plate so that the minimum factor of safety against failure of the concrete due to bearing is 2.5. The failure bearing stress for concrete is (sfail)con = 25 MPa
The truss shown consists of wooden members. Knowing that each member has a 50 x 50 mm. square cross-section and that each pin has a 12mm diameter, determine the maximum value of the average normal stress (a) in member BD. (b) in member DE. 50 kN 40 kN 2m: 2m Sm Answers should be in MPa.
1. A 20-mm-diameter rivet joins the plates that are each 110 mm wide. The allowable stresses are 120 MPa for bearing in the plate material and 60 MPa for shearing of rivet. Det. (a) the value of P (b) the minimum thickness of each plate; and (c) the largest average tensile stress in the plates. CO 110 mm 20-mm 0
The three suspender bars are made of A992 steel and have equal cross-sectional areas of 450 mm2. Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. Use E = 200 GPa B 60 kN 2 m 40 kN E F1m--1m--1 m--1m-
When the temperature is at 30°C, the A-36 steel pipe fits snugly between the two fuel tanks. When fuel flows through the pipe, it causes the temperature to vary along the pipe as T = (5 3 x2 - 20x + 120)°C, where x is in meters. Determine the normal stress developed in the pipe. Assume each tank provides rigid support at A and B.
Problem 2: The center post B of the assembly has an original length of 124.8mm whereas posts A and C have a length of 125mm. If the caps on top can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross-sectional area of 400mm2. EAI = 70 GPa loomn A
Problem 2 (for all students). Determine the state of stress, the principal stress and the max in- plane shear stress at point B on the cross section of the pipe at section a – a. Indicate the results on a differential element at the point. a 300 mm B, 300 mm a |6 kN B.50 mm TA - 40 mm Section a - a
STRENGTH OF MATERIALS The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure stress for steel is 360MPa, determine the minimum thickness t of the pipe if it supports the force of 600KN. Use a factor of safety against failure of 1.50. Also, find the minimum radius r of the base plate so that the minimum factor of safety against failure of the concrete due to bearing is 2.50. The failure bearing stress for concrete is 28MPa.
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
dAB The bracket BCD as shown in the figure is subjected to two forces, 50 KN and 10KN. a. If the control rod AB is made of a steel having an ultimate normal stress of 600MPA, determine the diameter of the 50KN 10KN rod for which the factor of safety with respect to failure will 0.6 m be 3.3. b. Suppose that the pin at C is to be made of a steel with an ultimate shearing stress of 350MPA. Determine the diameter of the pin C for which the factor of safety with respect to shear will also be 3.3. |-03 m- -0.3 m c. Determine the required thickness of the bracket supports at C knowing that the allowable bearing stress of the steel used is 300MPA. Ultimate Strength Factor of Safety Allowable Strength
The shaft is made of L2 tool steel, has a diameter of 40 mm, and isfixed at its ends A and B. If it is subjected to the couple, determine themaximum shear stress in regions AC and CB. Take Gst = 75 GPa
A horizontal rigid bar ADB of length 3m is pinned to a support at A and held by an inclined wire CD and vertical wire BE. The wires CD and BE are made of steel with diameter of 10 mm and 15 mm, respectively. Determine P if the allowable normal stress for CD and BE is 250 MPa Show complete solution. Thanks