A 440V, three phase source supplied the following impedances connected in parallel: mesh connected impedance of 8+j9 ohms; star connected impedance of 4-j6 ohms; delta connected impedance of 5+j 8 ohms; and wye connected impedance of 7+8 ohms. Solve for the combined power factor and its total power drawn from the source? ...

A 440V, three phase source supplied the following impedances connected in parallel: mesh connected impedance of 8+j9 ohms; star connected impedance of 4-j6 ohms; delta connected impedance of 5+j 8 ohms; and wye connected impedance of 7+8 ohms. Solve for the combined power factor and its total power drawn from the source? ...

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.45P: Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at...

See similar textbooks

Similar questions

The Figure shows a balanced Y-A 3Ø circuit. The phase voltages of the Y-connected source are V, = 11020°, V, = 1102 - 120° and V. = 1102120°, Volts. The line impdedances are Z,=10+j5 Q each. The impedances of the A-connected load are ZA = 75+j255 N each. Determine: Line Currents, Phase Currents (load), Power drawn by the load. Ve ZA Vb
A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.
In a balanced delta connected 3-phase circuit, has resistance 16 ohm and inductive reactance 12 ohm, connected to a 230V,50HZ 3-phase supply voltage, then total power delivered to load is Select one: a. 5397.7W b. 6.34KW c. 16.34KW d. NONE OF THESE
VAZ-120 V4120° Z₁ ZA Three-phase source Feeder lines Balanced load In the above circuit diagram, we have source impedance Zg = 0.05+j0.15 ohm, Z, = 0.1+j0.2 ohm and per phase impedance in the balanced Delta connected load, Z₁ = 12+j9 ohm. RMS value of source voltage is 200 volt. Phase sequence is as shown in the diagram. RMS value of current lc = ampere Phase angle of le= degree RMS value of line voltage VCA = volt I B lc c JAB Inc ICA
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Draw Wye- Delta three phase transformers connection ( no-load and full-load) in Lt-spice
1. The following are the given for the circuit below: VRY = 220 cis 0°, VYB = 220 cis -120° and VBR = 220 cis -240°. IR = 10 cis 0°. The load is balanced and delta connected. Determine the: (a) Impedance per phase (b) Current per phase (c) Line currents. B R reellle relllle momm Y RY Iy IB ĪR B R ZBR VYB ZRY
A balanced 3-phase delta load is going to be connected across a 230 V, balanced 3-phase source. In connecting this load to the source, three-line conductors with impedances of 4 + j3 ohms each are used. If the impedance per phase of the delta load is 12 – j5 ohms each, what is the total line loss in the three-line conductors in kW?
The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the line-to-neutral voltages are always equal to zero. (a) False (b) True