8. Which of the following features is required for proper sterilization by autoclave? a. Complete sealing of all openings with foil. b. Allowance for steam access to all surfaces. c. Vigorous boiling liquids. d. Fixed process time regardless of the amount of item. e. Excess hydrostatic pressure to ensure that all water exists within the liquid phase.

8. Which of the following features is required for proper sterilization by autoclave? a. Complete sealing of all openings with foil. b. Allowance for steam access to all surfaces. c. Vigorous boiling liquids. d. Fixed process time regardless of the amount of item. e. Excess hydrostatic pressure to ensure that all water exists within the liquid phase.

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter80: Crystallization: Purification Of Solids

Section: Chapter Questions

Problem 4P

See similar textbooks

Similar questions

Volumetric pipettes are designed to deliver a precise amount of liquid, but only if you a. submerge the end of the pipette into a solution you are delivering. b. allow the pipette to drain freely, and leave any residual solution in the pipette. c. hold the pipette at a 45 degree angle and ensure that all the liquid is delivered.
1. Define sparging. What is the significance of this step in an HPLC analysis? 2. What are the two types of pre-column? What is the purpose of each type? 3. What are the two types of packing used in HPLC column? Describe each type. Please answer numbers 1-3. Need asap
10. Which is a way to induce crystal growth if no crystals are forming upon a. scratch air-liquid interface on flask with a glass rod or spatula b. add a seed crystal c. boil off excess solvent volume d. all options are possibilites
1. What is drying to a constant weight? 2. Aside from sieving, what other methods are used to determine particle size. Give and describe briefly at least two methods.
Choose the appropriate techniques for degassing the mobile phase of HPLC. I. Ultrasonic II. Boiling III. Sparging IV.Filtering A. I and II B. Il and III C. I and III D. III and IV
Arrange the following steps in the correct order. I. Prepare the separatory funnel. II. Mix and release pressure. III. Add the solution to be extracted and add the extracting solvent. IV. Collect the organic layer. a. I, II, III, and IV b. I, III, IV, II c. I, III, II, IV d. IV, II, I, III
why should a small volume of the cold solvent be used for rinsing the pure crystal? (recrystalization)
Is the separation 100% complete after evaporation process? Explain.
Standard Preparation: 1. Weigh 10 mg of the Acetaminophen RS accurately and dissolve in 15 ml of methanol. Shake well. 2. Add 85ml of water to adjust the volume to 100 ml. 3. Pipet 5 ml from the stock solution and dilute to 50 ml with water. Test Preparation: 1. Weigh the 10 tablets individually and record on the worksheet provided. Powder 10 tablets and weigh a portion of the powders equivalent to 100mg. 2. 3. Transfer the powders into 100 ml VF. 4. Add 15 ml of methanol, shake to dissolve and dilute with water to the volume to make 100 ml. 5. Pipet 1 ml from the previous solution, transfer it into a 100-ml volumetric flask and dilute with water to volume. Instrument: UV-Vis Spectrophotometer Blank: water Cell- 1cm quarts cell Wavelength:243 nm Procedure: 1. Turn on the power switch. Allow the instruments to warm up for at least 20 minutes to stabilize the source and detector 2. After the warm up period, set the desired wavelength using the UP and DOWN arrows. 3. Using the MODE Key,…
The following conditions may not cause tailing EXCEPT a. Thick filter paper as the stationary phase b. Uncovered chamber c. Volatile solvent d. Heavy sample spotting
In a liquid – liquid extraction, what is preferable? Three extractions with a small volume or one extraction with a large volume. Explain briefly.
Liquid extraction What can you do if you don't know which layer is which in an extraction procedure? Explain