60 mm b Bottom Plate f100 mm Top Plate Ț100 mm t100 mm 150 A Plate with width of 400 millimeters and thickness of 12 millimeters is to be connected to a plate of the same width and thickness by 34 millimeters diameter bolts, as shown. The holes are 2 mm larger than the bolt diameter. The plate yield strength is Fy = 248 MPa, Fu = 400 MPa. It is required to determine the value of b such that the net with along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. The effective area is also the net area. a Calculate the value of b in millimetres. b Calculate the value of the net area for tension in plates in square millimetres. c Calculate the value of P in kN so that the fracture on net area governs.

60 mm b Bottom Plate f100 mm Top Plate Ț100 mm t100 mm 150 A Plate with width of 400 millimeters and thickness of 12 millimeters is to be connected to a plate of the same width and thickness by 34 millimeters diameter bolts, as shown. The holes are 2 mm larger than the bolt diameter. The plate yield strength is Fy = 248 MPa, Fu = 400 MPa. It is required to determine the value of b such that the net with along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. The effective area is also the net area. a Calculate the value of b in millimetres. b Calculate the value of the net area for tension in plates in square millimetres. c Calculate the value of P in kN so that the fracture on net area governs.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.2.10P

See similar textbooks

Similar questions

ISWB600 Braket palte=11mm p=450KN E=270mm p=55mm bolt size =M20
Agui - 4550/2 =2276 two plates each with thickness t = 16 mm are bolted together with 6-22 mndia. bolts forming alap Joint - Bolt spacing are follows St=40mm S2 - 80mm, 53= 100mm effective bolt hole dia is 25mm A36 is used. Compute the allowable tensile strength t = 16 mm ob 27 40 60 80 40 +=16mm S1-40 S2-100 52-40 P 7 @ 4umm
Prepare an excel file and to find a) area of the bolt, b) Average Shear Stress Bolt c) Bearing Area Stress and d) allowable stress. Applied force range – 500 to 1000 N (in step of 100 N) Bolt diameter range – 10 to 25 mm (in step of 5 mm) Plate thickness – 10 mm Consider ultimate tensile strength as 460 N/mm2. And consider factor of safety as 1.5.
1. Please check the safety of bolt connection in the figure below, where F=100KN (design value) and ej=300mm. For the M22 ordinary bolt of grade C, f =140 N/mm? and f" =305 N/mm?. (The unit of length is mm, and ignores the weld mark in the figure.) F %3D 160 b0 オ 80 4=10 |205 4=121 [8 00S
WHERE: BOLT DIAMETER = 22mm Fy = 241Mpa Fu = 414Mpa
sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the max
A plate with width of 400mm and thickness of 12mm is to be connected as shown in the figure. The holes are 2mm larger than the bolt diameter. The plate is A36 steel. Bolt diameter is equal to 34mm. It is required to determine the value of “b” so that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. Questions: 1. Determine the value of “b” in millimeters. 2. Determine the net area for tension in plates in square millimeters. 3. Determine the design strength for LRFD. 4. Determine the allowable strength for ASD.
tf Sec Ag tw W16x100 29.4 0.585 0.985 Bolt (7/8 in) A structural analysis was done for -1 the steel section whose shape and characteristics are shown below, and the outputs were arranged in the table below. Choose the appropriate amount, knowing that .all numbers are in units (ksi, in) O fy ( 36 fu 0.85 20.149 584.3 635.04 58 D(bolt) 7/8 P Maximum tensile force (P) that can be exerted Effective cross- sectional area (Ae) The value of T1 Modulus M (mo) !
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
Determine the design strength of an UNP300 with four lines if 20 mm diameter bolts in standard holes, as shown in the Figure below. 1= 20 mm 60 60 60 60 60 60, 60, 60, 60,60 UNP 300 F, = 370MPA F = 240MPa o o оо o o o o
A bolted connection shown consists of an angular section L 150mmx100mm x8mm. Bolt diameter = 18mm. Determine the effective net area of the section. (Ae). Properties of an L150x100x8: Area = 1,894 mm2 Fy = 248 MPa Fu = 400 MPa x = 23 mm y = 48 mm 50 50 50 50 50 50 150 40 www.AwNNO 60 100 50 P
Determine block shear strength of tension member shown in figure if grade of steel is Fe-410 ISA 100 × 75x8 mm 50 100 55 35 O 20 mm dia bolt hole