4. Figure 2 shows a logic circuit with output F Figure 2. Logic circuit with gate I (AND), gate II (AND), gate III (NOT), gate IV (AND), gate V (EXOR) and gate VI (OR) a. Find the Boolean expression of output F. b. The simplified Boolean expression of Output F. c. If the input A and C were High and Input B was Low, what is output F:

4. Figure 2 shows a logic circuit with output F Figure 2. Logic circuit with gate I (AND), gate II (AND), gate III (NOT), gate IV (AND), gate V (EXOR) and gate VI (OR) a. Find the Boolean expression of output F. b. The simplified Boolean expression of Output F. c. If the input A and C were High and Input B was Low, what is output F:

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
Task 6: Simplifying Boolean functions in EWB using the logic converter Simplify the following Boolean expression in EWB using the logic converter F (A, B, C) = AB'C'+ A'B'C'+ A'BC'+ A'B'C
For the input waveforms in Figure , what logic circuit will generate the output waveform shown? Explain in detail for each. Inputs B Output X Inputs B Output X
A B Prepare the truth table of the logic circuit (logic circuit) on the right. Then, using the truth table, write the function you have obtained according to the SOP (minterm) without any simplification and draw the logic circuit for the new function you have obtained. Make sure that the circuit you have drawn is understandable, the function you have written and the truth table are readable.
For a ((A+B)' + (A'B')) Boolean equation, with the input waveforms as shown in Figure 2, which output waveform is correct? INPUT A INPUT B OUTPUT a OUTPUT b OUTPUT C OUTPUT d- Figure 2 Output b Output a Output d Output c A full adder logic circuit has Three inputs and three outputs. Three inputs and two outputs. Two inputs and one output. Two inputs and two outputs.
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
Basic Combinational Logic Circuits 2. Write the output expression for logic circuit: A B B X
A three input logic functipn will provide a logic high output only when twp (and two only) of the inputs are logic highs. For all other input possibilities, a logic zero is provided on the output. What is the logic expression? A. Y=A'B'C+A'BC'+AB'C' B. Y=AB'C+A'BC+ABC' C. Y=AB'C+ABC+A'B'C' D. Y=ABC'+AB'C+A'B'C'
Build a truth table and draw the output wave form for the following logic gates shown in Figure Q2. A o B Co Do E o D D Figure Q2 Z
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
Design a combinational circuit with 3-inputs and 1-output. The output is equal to logic-1 when the binary value of the input is less than 3. And the output is logic-0 otherwise.
1. a. i. Draw the gates required to build a half adder are ii. When simplified with Boolean Algebra (x + y)(x + z) simplifies to : iii. The output of a logic gate is 1 when all its inputs are at logic 0, the gate is either :