3) This 65-lb cylinder is placed on the slope with an angle of 18 degrees and released from rest. If the cylinder rolls without slipping, what is its angular acceleration? Is the angular acceleration dependent or independent of the cylinder's weight? Is the angular acceleration dependent or independent of the cylinder's radius? 01 r = 0.5 ft

3) This 65-lb cylinder is placed on the slope with an angle of 18 degrees and released from rest. If the cylinder rolls without slipping, what is its angular acceleration? Is the angular acceleration dependent or independent of the cylinder's weight? Is the angular acceleration dependent or independent of the cylinder's radius? 01 r = 0.5 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 13-kg wheel is rolling under the constant moment of M= 89 N·m. The wheel has radius r= 0.47 m, has mass center at point G, and the radius of gyration is kG = 0.28 m. The coefficients of friction between the wheel and the ground is ls = 0.26 and uk = 0.15. If the wheel rolls while slipping, determine the angular acceleration of the wheel (in rad/s2). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s2. M Your Answer: Answer
1. Part (1): 4.5 kg wheel has an outer radius of 480 mm rolls down an incline starting from rest. The wheel radius of gyration is 0.35 m. Determine the linear and angular velocities if it rolls down without slipping and descends a height of 1.5 m. Analyze the energy transfer in this mechanical motion by comparing the energy value before and after. In case there is slipping condition, would the acceleration be uniform, and briefly explain how this will affect the energy transfer in the belt and the estimated efficiency value (no more than 20 words) h Figure.1: Rolling wheel on the down slope 2. Part (2): Derive the energy equation for potential, linear kinetic, angular kinetic and strain energy. Explain using simple sketches your derivation and state the main assumption for this effect of energy transformation
2. A cord is wrapped around a homogeneous disk of radius r = 0.5 m and mass m = 14. 25 kg. If the cord is pulled upward with a force T of magnitude 171 N, determine a. the acceleration of the center of the disk, b. the angular acceleration of the disk, c. the acceleration of the cord. T 0.5 m Go A Draw the Free Body Diagram.
At what position (d) you will place the pencil horizontally so that when it is released from rest, it will experience maximum angular acceleration The pencil has a mass (m} kg, and total length of 2. Bm. Consider the pencil as a uniform rod. Assume that the pencil will purely rotate about "O
The 17-kg wheel is rolling under the constant moment of M = 85 N-m. The wheel has radius r= 0.50 m, has mass center at point G, and the radius of gyration is kg = 0.20 m. The coefficients of friction between the wheel and the ground is ls = 0.27 and Hk; = 0.22. If the wheel rolls while slipping, determine the angular acceleration of the wheel (in rad/s?). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. M G
Question 2 A car has a mass of 4 Mg and the center of mass at G = 400mm from the ground. The front wheels are 1.3 m and rear wheels are 0.8 m from the centre of gravity. Coefficient of kinetic friction between the wheels and the road is 0.2. Determine the acceleration if the rear driving wheels are always slipping and the front wheels are free to rotate. Neglect the mass of the wheels.
The slender 8-kg bar AB is horizontal and at rest. The spring has an unstretched length sọ of 1 m and a spring constant of 15 N/m. the length of the bar AB is l1.Sm Find the angular velocity when e - 45° when the bar has rotate clockwise - 45° after being released. Give your answer with 2 decimals and include the sign
1. The 20-kg flywheel has a radius of gyration kg = 0.5 m about the axis of its attached shaft (O-0). It is at rest when subjected to a torque that rises uniformly from 0 to 2 N-m over 3 revolutions, then holds at a constant 2 N-m for the remainder of the motion. What is the angular velocity of the flywheel after 10 revolutions? Give your answer in RPM.
The thin rectangular block is supported at its corners by small rollers resting on smooth horizontal surfaces. If b = 0.5 m and h= = 0.3 m, calculate the magnitude of the angular acceleration of the block at the moment when the supporting surface at B is suddenly removed. Present your answer in rad/sec² using 3 significant figures. h B
The 16-kg wheel is rolling under the constant moment of M = 60 N-m. The wheel has radius r= 0.50 m, has mass center at point G, and the radius of gyration is kg = 0.23 m. The coefficients of friction between the wheel and the ground is ls = 0.28 and Uk = 0.14. If the wheel rolls without slipping, determine the angular acceleration of the wheel (in rad/s?). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. M
The 35 lb slender rod AB is 277 in. long and at rest in a horizontal position supported by a spring located at h = 226 in. from the suspension cable at B. If the cable at B fails, answer the following 1) Part A: Determine the magnitude of the acceleration of end A. 2) Part B: Determine the magnitude of the acceleration of end B. 3) Part C: Determine the angular acceleration of the rod.
5. Can you use Newton's third law to relate pairs of forces shown in different force diagrams? 6. Is there a relationship between the angular acceleration of the disk + ring system and the acceleration of the hanging weight? To decide, examine the accelerations that you labeled in your drawing of the equipment. 7. Solve your equations for the moment of inertia of the disk + ring system as a function of the mass of the hanging weight, the acceleration of the hanging weight, and the radius of the wheel. Start with the equation containing the quantity you want to know, the moment of inertia of the disk + ring system. Identify the unknowns in that equation and select equations for each of them from those you have collected. If those equations generate additional unknowns, search your collection for equations that contain them. Continue this process until all unknowns are accounted for. Now solve those equations for your target unknown. 8. For comparison with your experimental results,…