3 Link OB is 20 mm wide and 10 mm thick and is made from low-carbon steel with Sy= 200 MPa. The pin joints are constructed with sufficient size and fit to provide good resistance to out-of-plane bending. Determine the factor of safety for out-of-plane buckling. 800 mm where F= 1250 N 400 mm F The factor of safety for out-of-plane buckling is 0.2807

3 Link OB is 20 mm wide and 10 mm thick and is made from low-carbon steel with Sy= 200 MPa. The pin joints are constructed with sufficient size and fit to provide good resistance to out-of-plane bending. Determine the factor of safety for out-of-plane buckling. 800 mm where F= 1250 N 400 mm F The factor of safety for out-of-plane buckling is 0.2807

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
Problem 2 Assume that Member AB may be considered as long and slender and consider only Euler buckling. What is the critical Euler buckling load and will Member AB buckle? What is the factor of safety of the compressive load with respect to the critical buckling load? Assume buckling only occurs in the plane of the paper. Note: E-30e6psi, I-6.36e-3 in', A-2.83 in², LAB-41.6 in, FAB-540 lb (compression). Also Member OB is 36 inches (3 ft) long. F=270 lbf 3 ft 3 60 A = 45270 LB, n = 83.8, buckles 48400 LB, n = A. Per B. Per C. Per = 1088 LB, n 897, does not buckle 2.02, does not buckle D. Per = 544 LB, n = 0.993, buckles E. None of These
4. Determine the design stress for bolts in a cylinder cover where the load is fluctuating due to gas pressure. The maximum load on the bolt is 50 kN and the minimum is 30 kN. The load is unpredict- able and factor of safety is 3. The surface of the bolt is hot rolled and the suface finish factor is 0.9. During a simple tension test and rotating beam test on ductile materials (40 C 8 steel annealed), the following results were obtained : Diameter of specimen =12.5 mm; Yield strength= 240 MPa; Ultimate strength= 450 MPa; Endurance limit = 180 MPa. [Ans. 65.4 MPa]
A factor of safety of 2.5 is used for the bolts in the assembly below. The ultimate shear stress of the magnesium alloy bolts is 20.0ksi. What should be the diameter of the bolts? 10 kip 5 kip 5 kip Diameter = in
(11) The figure shows a connection that employs three SAE grade 5 bolts. The tensile shear load on the joint is 5400 lbf. The members are cold-drawn bars of AISI 1020 steel. Find the factor of safety for each possible mode of failure. (Ans./ 3.26, 5.99, 3.71, 5.36) in- 글im 16 UNC in I in -24 in-
5. A toggle device is used to compact scrap steel as shown below. If a Safety Factor of 3.5 is desired, and all the connections are pinned, design the 2 links of the toggle to have a circular cross-section and to be made from steel with Sy = 151 ksi and E = 30000 ksi. The force required to crush the shavings is 5000 lb. -Shavings Crushing force = 5000 lb 60 in- 15° 12 Toggle links- Applied force 60 in D = ? Section A-A Length typical both links
The following data is given for th4e bracket illustrated below. P=25 kN, e = 100 mm, 11 = 150 mm, 12 = 25 mm. There is no pre-load in the bolts. The bolts are made of plain carbon steel 45C8 (oy = 380 N/mm²) and the factor of safety is 2.5. Using the maximum shear stress theory, specify the size of the bolts. cessibility: Investigate 11€
Question 3 A typical Can dimensions are given as 63 mm in diameter, 120 mm in height and 0.1 mm thickness. These dimensions were measured on an aluminium beverage can which was carefully cut in half and measured the wall thickness and can diameter. Calculate the critical buckling load for the can and indicate if this is greater than or less than your weight. Does the can buckle? Assume the yield strength is 180 MPa and the elastic modulus is 69 GPa. A= 1= rg= The slenderness ratio is: 0J = x10^-9 m^4 The slenderness ratio is: Johnson equation )/( x10^-5 m^2 The buckling load P= m The buckling load An MPa N ) =
A cylinder head stud has a diameter of 14mm at the bottom of the thread. If the maximum ten sile stress allowed in the material is 30MPa. Calculate the safe load the stud can carry.
An M 14 x 2 hex-head bolt with a nut and a 14R washer under each of bolt head and the nut is used to clamp together two 18-mm steel plates. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the bolt stiffness. The bolt stiffness kb is 592.69 MN/m.
Use F.S. 2 against buckling. (Figure 1) Figure 4 ft 1 of 1 D 3 ft Part A It P=20 kip, determine the required minimum diameter of the A392 steel sold sind BD Express your answer to three significant figures and include the appropriate unit d=2.5 B μA
V-links "Im crank arm раper rolling machine forks rod off-loading station air cylinder fork lift truck Determine the critical load on the air-cylinder rod if the crank arm that it rotates is 0.3 m long and in the position with the largest compression of the rod its length equals 0.5 m. The 40-mm-dia rod is solid steelwith a yield strength of 400 MPa. Assume the rod is a fixed-pinned column. Use a theoretical value for the effective length factor. Express your answer to three significant figures and include the appropriate units. HA Per = 1026 kN