V-links "Im crank arm раper rolling machine forks rod off-loading station air cylinder fork lift truck Determine the critical load on the air-cylinder rod if the crank arm that it rotates is 0.3 m long and in the position with the largest compression of the rod its length equals 0.5 m. The 40-mm-dia rod is solid steelwith a yield strength of 400 MPa. Assume the rod is a fixed-pinned column. Use a theoretical value for the effective length factor. Express your answer to three significant figures and include the appropriate units. HA Per = 1026 kN

V-links "Im crank arm раper rolling machine forks rod off-loading station air cylinder fork lift truck Determine the critical load on the air-cylinder rod if the crank arm that it rotates is 0.3 m long and in the position with the largest compression of the rod its length equals 0.5 m. The 40-mm-dia rod is solid steelwith a yield strength of 400 MPa. Assume the rod is a fixed-pinned column. Use a theoretical value for the effective length factor. Express your answer to three significant figures and include the appropriate units. HA Per = 1026 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.18P: The piston in an engine is attached to a connecting rod AB, which in turn is connected to a crank...

See similar textbooks

Similar questions

A leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches apart and the system should carry a load of 400 lbs. If the thickness of the available bronze plate is 1“ and Sy = 80 ksi, what leaf width is required at FOS = 8?
For the same question, the M25 Screw will be used when pressing the Nut Wheel onto the shaft. Assuming that the force that the nut needs to suppress is Fçak=1218 kgf (it was found in the previous question, but we don't use it), what should the minimum NUT HEIGHT be in mm to create this force safely? (Screw and Nut's surface safety pressure Pem=45 N/mm2 Screw base diameter d1= 21.5 mm. (Calculate the pitch (h=?) according to the given ones, considering that metric screw is used!)
Question 4A close-coiled helical spring is to have a stiffness of 90 kN/m and is to exert a maximum force of 3.7 kN. If the mean diameter of the coils is 80 mm, and the maximum stress is not to exceed 300 MPa, calculate the required number of coils and the diameter of the steel rod from which the spring should be made (G=80 GPa).
4 dia 16 R. 3. The grip strengthener shown in Fig. 1 is composed of a helical spring made of 4 mm diameter A227 hard-drawn Wire clip wire. The main coil has an outer diameter OD = 32 mm and a total number of body turns N= 3.5. During operation, assume that the force applied to the handles Molded 112.5 plastic handle 87.5 occurs at a distance of 50 mm from the base of the handle. Using a design factor at closure of n, = S,lo,= 1.1, calculate the torsional spring constant k' and the force F, required to close the handles. 75 Fig. 1
An aluminum ring has an outside diameter of 12.0 mm and an inside diameter of 10 mm. If the ring is short and is made of 2014-T6, compute the 3-13. force required to produce ultimate compressive failure in the ring. Assume that s, is the same in both tension and compression.
a helical compression spring with squared and ground ends is ti be made of a steel wire 79 gpa and presetting is to be used. the operation load of the spring can be considered static. If the maximum working force is 292 N and a force of 35 N is required when the spring is 30 mm longer, determine the spring constant k
A horizontal load Pis applied to an assembly consisting of two inclined bars, as shown in the figure. The cross-sectional area of bar (1) is 1.65 in.?, and the cross-sectional area of bar (2) is 1.85 in.?. The normal stress in either bar may not exceed 23 ksi. Determine the maximum load P that may be applied to this assembly. Assume dimensions of a = 15.0 ft, b = 10.0 ft, and c = 14.5ft (1) b. Part 1 Determine the allowable force F1 in member (1) and the allowable force F2 in member (2). FLallow kips F2,allow kips i Attempts: 0 of 1 used Submit Answer Save for Later Part 2 Part 3 Find the ratio, (F1 /F2), where F, is the force in member (1) and F2 is the force in member (2). Both bars are in tension, so these forces are both positive according to the sign conventions. FIF2 = i
A safety valve spring having 9 and 2 coils has the ends squared and ground. The outside diameter of the coil is 115 mm and the wire is 13 mm. It has a free length of 203 mm. The length of which this spring must be initially compressed to hold a boiler pressure of 1.38 MPa on the seat of 32 mm diameter. Modulus of rigidity is taken as G=80GN/m?. a. Find the force acting on the valve set. b. Determine the mean diameter c. Determine the spring index d. Find the spring deflection e. Find the operating length f. Calculate the solid length g. Calculate the deflection of solid length h. Compute the solid force i. Compute the Wahl factor
The specifications for a coil spring are known. Infinite fatigue life is required, using a safety factor of 1.3 applied to the maximum load only. The fatigue strength can be represented by a line between τmax= 600, τmin= 0 and τmax= τmin= 900 MPa.Assume both end plates are in contact with nearly a full turn of wireand that the end plate loads coincide with the spring axis.Determine a suitable combination of d, D, and N, if C = 8
For Probs. 1-3, (a) draw the free-body diagrams for the entire assembly (or structure) and each of its parts. Neglect friction and the weights of the members unless specified otherwise. Be sure to indicate all relevant dimensions. For each problem, (b) determine the total number of unknown forces and the total number of independent equilibrium equations. Problem 1 500 N 500 N 1 m 500 N (b) (c) Figure 1 Problem 2 -- Ift 4 ft -1.8 ft 100 lb F1.8 ft - 100 lb 100 lb (а) (b) (c)
The corediameter of the double start square threaded screw having a pitch of 12mm is 50 mm. A load of 18kN is lifted through a distance of 180mm. Find the work done(in Joule)in lifting the loadand the efficiency of the screw, when 1. The load rotates with the screw, and 2. The load rests on the loose head which does not rotate with the screw. The external and internal diameter of the bearing surface of the loose head are 60 mm and 10 mmrespectively. The coefficient of friction for the screw is 0.11,whilefor the bearing surface is 0.13.
three (3) different cylinder mude from Steel, Aliminurn and Uronze are jointed Logether to torma composite structure and fixed to vall suport. Three (3) axial forces acted on the structure as shown. The fallowing valuc was alroady cietermined: 1 KN to the nght -3kN Tensioa -2 kN compression Reaction al A Internal force for Aluminum Interral force for Brone Este= 200 GPa; Ealumin 70 GPa Egmee 83 GPa Determine Ue eiongalion (A) for ach section: Steel Aluminum Bronve Aluminum A= 400 mm Bronze A-200 mm Steel A S00 m 2P 4P SP 2.5 m 2.0 m 1.5 m