21. Draw the logic diagram of a 4-bit register with four D flip-flops and four 4x1 multiplexers with mode selection inputs si and so. The register operates according to the following function table So Register Operation No change 1 Complement the four outputs 1 Clear register to 0 (synchronous with the clock) 1 1 Load parallel data

21. Draw the logic diagram of a 4-bit register with four D flip-flops and four 4x1 multiplexers with mode selection inputs si and so. The register operates according to the following function table So Register Operation No change 1 Complement the four outputs 1 Clear register to 0 (synchronous with the clock) 1 1 Load parallel data

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Select a suitable example for for combinational logic circuit. O a. None of the given choices O b. De-multiplexer O c. PLA O d. Latches
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
Electrical Engineering Draw 2, 1 bit ALUS to create a basic 2 bit ALU. the carry out and carry in bits must ripple across. The ALU should subtract/add, logical NOR, logical AND, and logical OR. Draw out the adding logic circuit
6- Set BX to 4567H, CX to FEDCH and SP to A59FH, then run the instructions: PUSH BX PUSH CX a. What is the new value of SP ? b. Display the memory locations where you pushed the values of BX and CX in the stack.
Problem 5 For the logic circuits shown below: determine the output F, write the true table, and draw the output F in proper relation to the given inputs with a timing diagram. a) B B F F b) B B F
Identify each of these logic gates by D A B A 40 B A AB AB B
ehcu.org/pluginfile 100% 10 / 11 locations, count how many times is 0 and how many times 1 is. Questions:- 1- Write a program in assembly language to perform the following logic ci BL CL DL [5100]- 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , LG
1. Design a combination circuit and write a logic circuit when there are 3 switches and 1 lamp, the lamp will light when there are at least 2 switches per circuit.
Select a suitable example for combinational logic circuit. O a. None of the given choices O b. Flip-flop O c. Half adder O d. Counters
Importance of pin PULL-UP in any microcontroller is O A. to save the power supply O B. to supply voltage to the pin O C. to protect the logic input from noise O D. to understand the logic input high
What is the function of the odd parity generator circuit? O a. produces an output of 'I' for even number of logic T O b. produces an output of '0' for odd number of logic T' O c. produces an output of '1' for odd number of logic T shift? What is the difference between a left logical shift and a left arithmet O a. logical shift feeds a '0' in the MSB O b. arithmetic shift feeds a '0' in the MSB O c. no difference