2. Draw an impedance diagram for the system whose one-line diagram is shown in Figure P5.15. The 36 and line-line ratings are as follows: Generator: 30 MVA, 13.8 kV, Xs = 0.10 p.u. Motor: 20 MVA, 13.8kV, Xs = 0.08 p.u. T₁: 20 MVA, 13.2-132kV, X, = 0.10 p.u. T₂: 15 MVA, 13. 8-138kV, X, = 0.12 p. u. Line: 20+ 10002 (acutal) Pick the generator ratings for the base in the generator section. Generator T₁ Dele 000 AY T₂ 080 2002 A YA -O Motor

2. Draw an impedance diagram for the system whose one-line diagram is shown in Figure P5.15. The 36 and line-line ratings are as follows: Generator: 30 MVA, 13.8 kV, Xs = 0.10 p.u. Motor: 20 MVA, 13.8kV, Xs = 0.08 p.u. T₁: 20 MVA, 13.2-132kV, X, = 0.10 p.u. T₂: 15 MVA, 13. 8-138kV, X, = 0.12 p. u. Line: 20+ 10002 (acutal) Pick the generator ratings for the base in the generator section. Generator T₁ Dele 000 AY T₂ 080 2002 A YA -O Motor

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

A synchronous generator has been synchronized to an infinite grid of 13.8 kV and 60 Hz. The generator prime mover C/C is such that the no-load frequency is 62.5 Hz and the power slope is 1 MW/Hz. The AVR C/C (The reactive power against the terminal voltage C/C) is such that the zero reactive power voltage is 14.6 kV, while the slope is 0.4 MVAR/kV. Calculate: (a) the kVA loading of the generator and its power factor. (b) the settings of the prime mover and AVR such that the generator delivers 3 MW at 0.85 lagging power factor.
5.7. In Figure P5.7, the voltages at a, b, and c are balanced 30. Transformers are ideal and have the same turns ratio. Find the voltages Va, Vic, and Vea in terms of Vab, Vher and V ca (a) Are they balanced 30? (b) If not, how would you reconnect the transformers to obtain balanced 36? a rele b 6 b' 000 ( Figure P5.7
Discuss the concept of reactive power and its role in grid stability.
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit
Q5/B: Explain delta-star connection of 3 ph transformers. What its advantages and disadvantages?
If, in one (360 degrees), all of the instantaneous power falls under positive loops (no negativeloops), the load must be:a. A resistorb. An inductor or capacitorExplain:
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
write all possible KCL and KVL equations. simplify all and in ascending order, with contsant at the right side of the equation.
A 120V adjustable frequency ac source is connected in series with a resistor, an inductor, and a capacitor. At 60Hz, the resistance is 5 ohms, the inductive reactance is 3 ohms, and the capacitive reactance is 4 ohms. Compute: (a)load impedance at 60Hz (b) value of the capacitance and inductance Explain each step.
3 X 0.1 1 2 XL = 0.2 to Eato oto O X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. (2 Marks) b) Find the bus voltages and line currents during the fault. (2 Marks)
Aside from the typical RLC circuit arranged in series, there exist that arranged in parallel as well (see Figure 3). In this configuration, the instantaneous voltages (and rms voltages) across cach of the three circuit elements are the same, and cach is in phase with the current in the resistor. The currents in C and L lead or lag the current in the resistor as shown in the phasor diagram (Figure 3b). By taking the instantaneous voltage across the AC source to be v(t) =V sin er and the instantaneous current provided by the AC source to be i(r) =, sin (er - ø). where V, and are the voltage and current amplitudes respectively, (a) (b) AV AV R. gure 3: (a) RLC circuit in parallel configuration and (b) phasor diagram for the RLC circuit. (a). Write the instantaneous currents across the three circuit elements in terms of angular frequency o, inductance L, and capacitance C. (b). Relate for the ratio of the rms voltage and current towards the ratio of the amplitude voltage and current. (c).…
The total reactive power consumed by the three-phase load(in VAr) is??