2. A pair of connected pulleys receive a force F = 100 N and P = 150 N as depicted in the image. The radius of pulley 1 is r₁ = 500 mm, and the radius of pulley 2 is r2 = 950 mm. The pulley system has a radius of gyration of ko = 0.5 m and mass of 50kg. Determine the following: 1. Reaction force in the x direction 2. Reaction force in the y direction 3. Angular acceleration of the pulley √₂

2. A pair of connected pulleys receive a force F = 100 N and P = 150 N as depicted in the image. The radius of pulley 1 is r₁ = 500 mm, and the radius of pulley 2 is r2 = 950 mm. The pulley system has a radius of gyration of ko = 0.5 m and mass of 50kg. Determine the following: 1. Reaction force in the x direction 2. Reaction force in the y direction 3. Angular acceleration of the pulley √₂

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

10 İnch, 300 B 20 Inch 5 ft Sinch 100 lb 16 ft Mass of the AB bar in the I profile form in the system loaded as shown in the figure 100 kg / m; Using magnitudes translated into the SI system of units; Question 3: the bearing response forces at point A and the pulling force acting on the BC cable (T) find the intensity
4. A student followed strictly correct procedure in the lab during the experiment of moment of inertia. He measured the mass and diameter of plastic cylinder with value of m = 0.36 kg and D = 0.1 m. The period of system without plastic cylinder is To = 0.667 s. The period of system with plastic cylinder T₁ = 0.92 s. Find: The spring constant K of the system. If a metallic cylinder and a plastic cylinder have same diameter and same thickness, which one has larger moment of inertia? Explain.
Figure below shows a rod with mass M = 100 kg, cross section area A = 10 cm². The rod is supported by 4 springs having stiffnesses of k = 1 MN/m. A tip mass with m = 120 kg is attached to the rod. Assume x is the degree of freedom of the equivalent system. The Young's modulus, E, is not known. If the natural frequency of the equivalent mass-spring system is 40 Hz, determine the Young's modulus, E. Assume the length of the rod is L = 5 m. Find the nearest answer. k ww E, A, M k F @www.ww wint L 195 GPa 179 GPa 116 GPa 45 GPa 236 GPa 000 00
Q1: The system shown has two masses. Beam of mass (Jo#m L² kg.m²) rotates about fixed point (O) and its free end is connected to disk rotates about fixed point (O₂). Consider all connecting links are massless and rigid. Find 1- The displacements of points A, B, and C in addition to the rotations of masses, all in terms of 0. 2- Find the equation of motion (EOM) in terms of 0. 3- What is the natural frequency of the system? 0 L/2 8 Energy methods A Jo=m L²2 L/2 Joz-m R² R C B C 128
Three rigid bodies (Nodes 2, 3, and 4) are connected by five springs as shown below. Assume that the bodies can only undergo translation in the horizontal direction. Horizontal force P2=1000 N and P4=2000 N is applied to Elements 2 and 4, respectively. The spring constants in (N/mm) are given as: kı=100, k2=250, k3=300, k4=700, and ks=200. Nodes 1 and 5 are fixed. Determine the nodal displacements and reaction forces at the walls. Show all the work by deriving each equation and moving equations in matrix form and then applying BC's and solving. Do not rename the nodes or elements! 3
For this problem, take a look at Figure 2. Assume that the rod is massless, perfectly rigid, and pivoted at point P. When the rod is perfectly horizontal, the angle 0 = 0, the displacement y = 0, and the spring is in neither tension nor compression. Gravity acts on the system (e.g. on mass M). We assume that y is a small displacement. A mass M is attached at the end of the rod. k Schen a 0 a F The equation of motion for the system can be derived to be: a 4aM0+ ak0 =-F-2Mg T y M Your tasks: A. Transform the rotational equation of motion, which is in 0, given above, to another variable, y, which is zero at the static equilibrium position. onical system in sta bace form. Using MATLAB or a calculator lues of INI. W 16 [N/m], and C. Derive the response of the system in the Laplace (s) domain. Use the static equilibrium value found in part A (Ost) as the initial value, (0), for the problem. Assume (0) and the force, F, are both zero. You may treat gravity as g = 10 [m/s²] for ease of…
For this problem, take a look at Figure 2. Assume that the rod is massless, perfectly rigid, and pivoted at point P. When the rod is perfectly horizontal, the angle 0 = 0, the displacement y = 0, and the spring is in neither tension nor compression. Gravity acts on the system (e.g. on mass M). We assume that y is a small displacement. A mass M is attached at the end of the rod. k Schen a 0 a F The equation of motion for the system can be derived to be: a 4aM0+ ak0 =-F-2Mg T y M Your tasks: A. Transform the rotational equation of motion, which is in 0, given above, to another variable, y, which is zero at the static equilibrium position. B. Represent the mechanical system in state space form. Using MATLAB or a calculator (just say what you used), calculate the eigenvalues of your A matrix for the following system parameters: a = 0.25 [m], M = 1 [kg], k = 16 [N/m], and F = 0 [N]. What do the eigenvalues say about the stability of the system? C. Derive the response of the system in the…
In the graph the force versus displacement of a spring is given (the spring is shown in a separate figure--see below). The x-axis range is ±2 cm. The y-axis range is tFs, where Fs = 220 N. How much work does the spring do on the block (the mass "m") when the block moves from x₁ = 7.6 cm to 4.3 cm? W J y F. X -1.5 -0.5 0 10.5 1 1.5 -F How much work does the spring do on the block (the mass "m") when the block moves from x; = 7.6 cm to -7.6 cm? W = Question Help: Read Submit Question m
QUESTION 18 The flywheel in Figure Q18 consists of two plates of mass m = 64 kg and thickness w = 0.050 m which are connected by arms of length 1 = 0.48 m into a rotating axis. An increasing moment M (N-m) is applied about the axis according to the expression M = 5t where t (s) is the time. Determine the time duration needed to accelerate the flywheel such that the plates reach a tangential velocity 20.0 m-s-1, if their initial velocity at time zero is 10 m-s-1. Provide only the numerical value (in seconds) to two decimal places (e.g. 10.25) and do not include the units in the answer box. m 1 M Figure Q18: Accelerating flywheel 1 m
Find the equivalent spring constant spring constant of the system. Say, k1 = 20 lb/in, k2 = 35 lb/in, k3=18 lb/in,k4 = 50 lb/in, k5 = 45 lb/in
Question 9: Figure 3 shows a mechanical system. The rod (with moment of inertia J) rotates about the pivot at only small rotation angles. As pictured, theta is positive clockwise. Attached is mass m, which moves positive to the right. When stationary in the position shown, all springs are undeflected. Using BOBODDY, find the mathematical model of this system assuming small rotation angle 0. Link, moment of inertia J k3 L₁ 12 5 Ꮎ wwww Figure 3: Mechanical System m k₂ b
Determine the equivalent spring constant of the system shown in the figure.