Answer should be: 1hr 50mins 40secs 19. A tank with a horizontal sectional area constant at 10m²and 4 m high contains water to a depth of 3.5 m. Thetank has a circular oriflce 5 cm in diameter and locatedat its side 0.5 m above the bottom. If the coefficient ofdischarge of the orifice is 0.60, find the duration of flowthrough the orifice.

Consider the diagram as shown below for the given system.

,2 A tank with a horizontal sectional area constant at 10m² and 4 m high contains water to a depth of 3.5 m. The tank has a circular orifice 5 cm in diameter and located at its side 0.5 m above the bottom. If the coefficient of discharge of the orifice is 0.60, find the duration of flow through the orifice.

,2 A tank with a horizontal sectional area constant at 10m² and 4 m high contains water to a depth of 3.5 m. The tank has a circular orifice 5 cm in diameter and located at its side 0.5 m above the bottom. If the coefficient of discharge of the orifice is 0.60, find the duration of flow through the orifice.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the Flow rate through the pump IS 0.1 mls of water, Find the pump head. The manometer reading is 100 cm Hg. given that the suction Side liameter is o.2 m and discharge side diameter is o.15 m 1oo cm Hg
Find the difference in pressure head and velocity of flow of an ail through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 116 mm. Take co-efficient of the pitot tube ("L shaped measuring instrument) as 0.97 and sp. gr of ail = 0.85 (Enter only the values in the boxes by considering units given in the bracket. Do not send the hand written answers to my mail Id) Difference in pressure head (unit in mm) = Velocity of flow (unit in km/hr)%3D
In a canal and the A Sluice gate Is a device that is fited In a Sluice fluid canal to operste cand control the fluid flow. Oil plon's In a canal and the sluIce gate has a breadHh 1r flow. Oil flows of 8m 3. 850k9/m cdensHy wide and bm deep. let the oil cdesHy Determine the Centre a pressure (CoP) on the sluice gate, gate of the slui cre Gate when the 01 1s level With the top 11
Find the discharge in nach pipe shown in fgure. The head available at A is 20m of water and the friction factor for each pipe may be taken 0.03. 100 mm diameter, 200m length B Atmosphere 100 mm diameter, 100m length 50 mm diameter
The Reynold’s number for fluid in a pipe of 10-in diameter is 2000. What will the Reynold’s number in a 6-in diameter pipe forming an extension of the 10-in pipe? Take the flow as incompressible.
3.A horizontal venturimeter with inlet diameter 30 cm and throat diameter 15 cm is used to measure the flow of oil of sp. gr. 0.8. The discharge of oil through venturimeter is 50 litres/s, find the reading of the oil-mercury differential manometer. Take Cd = 0.98
An orifice meter with orifice area 931 mm² is inserted in a pipe of area 1862 mm2 .The pressure B4. difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 75 cm of mercury. Find the rate of flow of oil of sp. gr. 0.75 when the co-efficient of discharge of the orifice meter = 0.6. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) Head of water (in m) The discharge of water through pipe (in Litres/sec)
B4. An orifice meter with orifice area 1039 mm2 is inserted in a pipe of area 2078 mm? .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 60 cm of mercury. Find the rate of flow of oil of sp. gr. 0.9 when the co-efficient of discharge of the orifice meter = 0.52. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) Head of water (in m) The discharge of water through pipe (in Litres/sec)
-Example the values. asystem total head. against for the initial condition, show below - give the Lallowiny data dynamic uiscosity of liquid Calculate capacity curve density S-1200 kgim3 Static head on Suction Side 7S-3m Static heac on discharge Side Zd= 7m inside diameter of pipe di = o.052m -pipe roughress E3D0.00045m. gas pressure aboue the liquid in the tank Side of the pump the Suction Ps= atmospheric pressure. gas pressure above the liquicd in the tank on discharge side of the pump. the dund Pd= atmesperic pressure
Determine the available suction head of a pump that is taking gasoline at 204 deg. C, from a closed tank with a pressure of 585 Kpa gage. The specific gravity of gasoline is 0.78 and its vapor pressure is 620 kpa absolute. The loss in the suction pipe is 0.5m and the pump centerline is located 3.60 meters above the gasoline level. answer is 4.47 how
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 110 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument ) as 0.9 and sp. gr of oil = 0.9 (Enter only the values in the boxes by considering units given in the bracket. Do not send the hand written answers to my mail Id) Difference in pressure head (unit in m) = Velocity of flow (unit in m/s) = Question 8 个

Consider a desired pump operating condition which adds 35 psi at a flow rate of 500 gpa to water. Ignore any changes in Kinetic or potential energy and assume isothermal flow (ie. Internal energy is constant, this is normal assumption we make when analyzing fluid flows in piping systems). Apply the energy balance only across the pump starting with full energy balance and simplifying to solve for the pump head symbolically. Then begin careful of unit, solve for pump head in feet. Given erosion 500 gpm P=62 lbs/ft^3 A- 10.5 ft B- 100.8 ft C- 50.1 ft D-80.7 ft