1)For the function given as f (X1 , X2 , X3 , X4 ) X1 , X2 will be defined as selection inputs and the output expression of the function is as follows. f = ∑(2,3, 5, 7,8,9,10,11) a) Realize the requested design by using 4x1 Selector (MUX). b) Determine the appropriate logic gates for X3 and X4 inputs of the circuit.

1)For the function given as f (X1 , X2 , X3 , X4 ) X1 , X2 will be defined as selection inputs and the output expression of the function is as follows. f = ∑(2,3, 5, 7,8,9,10,11) a) Realize the requested design by using 4x1 Selector (MUX). b) Determine the appropriate logic gates for X3 and X4 inputs of the circuit.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

An X-input exclusive-OR gate and a Y-input exclusive-OR gate (where X=3, Y=4 have their outputs connected to a 2-input exclusive-NORgate. Do the following:a) Draw the logic diagram and analyze the logic expression of the output (in standard SOPform).b) List out all essential prime implicants.
Design a 3-bit counter that counts the following sequence: 7,5, 3. 1.0.7, 5. 3, 1, 0, 7. etc. Using the sequential design technique that starts from a state diagram, draw the state table. minimize the logic. and draw the final circuit. The outputs of logic circuit are 2 = Qo Q1. I, = Qo.Qi + Qo.Qi, Io = Qo.Q2, Cont2 = Qj Q2 Cont1 = Qu Q2. Cont0 = Q2 Qo.Q1. h = Qo.Qi + Qo.Q1, Io = Qo Qz Cont2 = Q, Q2 Contl = Qo Q2 Cont0 = Q2 Qo Qı Ij = Qo.Q, + Q».Qı, Io = Qo. Q2. Cont2 = Qj Q2. Contl = Qo.Q2. Cont) = Q2 L = Qo.Qı. I¡ = Q. Qj + Qu Q Io = Qv.Qz Comt2 = Q, Q, Contl = Q Q2 Cont0 = Q2 !! fefsto How much will be per-product cost and th
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
1)For the function given as f (X1 , X2 , X3 , X4 ) X3 , X4 will be defined as selection inputs and the output expression of the function is as follows. f = ∑(2,3, 5, 7,8,9,10,11) a)Determine the appropriate logic gates for X1 and X2 inputs of the circuit. b)Realize the requested design by using 4x1 Selector (MUX).
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
d) Draw the schematics of 4-bit synchronous and asynchronous MOD-8 counters and comment on their pros and cons. e) Calculate the noise margin for a logic gate with the following logic levels: VIL = 1.1 V, VIH = 3.2 V, VOL = 0.6 V, VOH = 4.0 V.
We want to design a circuit to detect prime numbers.The input of the circuit is a 4-bit binary number and the output is a single bit and should show one when the number is prime and zero otherwise.B. Implement the circuit using a 4× 1 multiplexer and combinational logic gates.C. Implement the circuit using only one decoder and one OR gate. What is the size of the decoder you use?
Figure Q2(e) shows a programmable logic array (PLA) unit with two inputs, four columns, and three outputs. Show the steps to implement a one-bit comparator using this PLA. Note that the output should have equal (EQ), less than (LT), and greater (GT) status. A, 02 Figure Q2(e)
In this assignment, you are required to design a circuit that counts and displays the sequence of the number 010430011092 . The number will then be displayed on a 7-segment display and changed every 1 second. The block diagram is as shown in Figure 1. Construct your design as follow: - (a) Design a combinational logic circuit that converts binary number to a sequence of the number 010430011092 and to be displayed on a single common anode 7-segment display. The logic circuit must be designed using 2-input NAND gate
a) Design a combinational circuit that would take a 3-bit binary number and generate an output if the input value in decimal is either divisible by 2 or 3. iii) Explain and show how you would implement this circuit using a 4-to-1 Multiplexer and other appropriate logic gates. Use a block diagram for the multiplexer.
For a combinational logic circuit of four bits Binary Coded Decimal (BCD) inputs and one output having following conditions: • if the equivalent decimal number of the BCD is even then output is 0 • if the equivalent decimal number of the BCD is odd then output is 1 Draw the truth table 20. i) ii) Find the simplified logic function using K-Map ii) Draw the logic diagram
6. For the follow logic circuit system, the output f is: 5 (A) ab. (B) a + b. (C) a'+b'. (D) a'b'. a b