1a. If an 8-bit binary number is used to represent an analog value in the range from 010 to 10010, what does the binary value 011001002 represent? 1b. If an 8-bit binary number is used to represent an analog value in the range from 32 to 212, what is the accuracy of the system? In other words, if the binary number is incremented by one, how much change does it represent in the analog value?

1a. If an 8-bit binary number is used to represent an analog value in the range from 010 to 10010, what does the binary value 011001002 represent? 1b. If an 8-bit binary number is used to represent an analog value in the range from 32 to 212, what is the accuracy of the system? In other words, if the binary number is incremented by one, how much change does it represent in the analog value?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

An analog voltage (0 to 5) volt is to be converted to 8 bit digital form. d. What is the error made in quantization of 2.2 volt as a percentage of the input.
please show work included 4. If a 6-bit binary number is used to represent an analog value in the range from -63 to 126, what is the accuracy of the system? In other words, if the binary number is incremented by one, how much change does it represent in the analog value?
Write hamming code for the data 0011 for the (i) Even parity (ii) Odd parity. Explain the process briefly
Please show work included 6. Assume a digital to analog conversion system uses a 7-bit integer to represent an analog temperature over a range of -27oF to 100oF. If the actual temperature being read was 40oF, what would be the closest possible value that the system could represent? Write the answer in a 7-bit binary number as well as in decimal. The answer should be in the following form 00010001 and -10oF a set of two numbers.
Which statement describe a digital signal? a. is a smoothly and continuously varying voltage or current. b. will take on finite set of voltage levels. c. take on all possible values of amplitude. d. can have an infinite number of values in a range
An analog voltage (0 to 5) volt is to be converted to 8 bit digital form. a. What is the resolution in volt. b. What is the digital representation of 2.2 volt. c. What is the largest quantization error as a percentage to full scale. d. What is the error made in quantization of 2.2 volt as a percentage of the input.
Q2) B) Use the SAR ADC to convert the analog voltage of (7.28 V) to 8-bit binary. If (VREF = 10V), determine the final binary answer and the percent error. O 01011101, 0.1974588% 11011101, 0.1974588% O 01011111, 0.1974588% O 01111101, 0.1974588%
(a). If I want to store 4-bit data 0110 and at 4th clock I want to extract all the stored bits, which shift register I should explain it with the help of circuit diagram and table. (b). Write comparison between Diode transistor logic and Transistor Transistor logic
) Convert from Binary to Decimal a) 101101011112 (b) 11001100110.110112 I) Using Double Dabble method, convert from Decimal to Binary (a) 1443.7187510 (b)1845.31010
A)What will be the frequency at C if the clock is 320 kHz? B) What is the modulo of the circuit? C) What is the output (in binary) after 737 pulses?
Suppose an analog-digital converter IC ('chip") inputs a voltage ranging from 0 to 3.5 volts DC and converts the magnitude of that voltage into an 8-bit binary number. How many discrete "steps" are there in the output as the converter circuit resolves the input voltage from one end of its range (0 volts) to the other (3.5 volts)? How much voltage does each of these steps represent?
Objectives: To demonstrate the operation, characteristics and design of a saturated bipolar transistor switch Material Needed : 1- 2N2222A NPN transistor 1- 1k ohms resistor 1 - 4.7k ohms resistor 1- 470k ohms resistor ELECTRONIC WORKBENCH Procedure 1. Construct the circuit shown in Fig 1-1. The circuit receives its input from data switch SW1. You will monitor the output at the collector with a voltmeter. +Vcc Rc =1K Vo OUTPUT [SPACEBAR] to switch [Space] Rg=470k VCE SW1 Figure 1-1