Question 5 With reference to 8086 Microprocessors Pin Assignment: 1) State the three groups of signals. b) What are the uses of AD1S-ADolines? c) (i) Briefly explain the operation of RD signal? (ii) Explain the function of Ready and INTR signals. d) (i) Explain briefly the function of MN/MX pin? (ii) What happens when a high is applied to RESET pin?

Question 5 With reference to 8086 Microprocessors Pin Assignment: 1) State the three groups of signals. b) What are the uses of AD1S-ADolines? c) (i) Briefly explain the operation of RD signal? (ii) Explain the function of Ready and INTR signals. d) (i) Explain briefly the function of MN/MX pin? (ii) What happens when a high is applied to RESET pin?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Rewire these two logic gate diagrams as circuits with IC (integrated circuit) Chips.
The circuit shown in the figure is an example of A.) AND gate b) SPDT electronic switch C) inverter D) OR gate
draw the curcuit diagram for 4 channel 4 bit multiplexer implemented using 4 channel 1 bit multiplexer. make sure that i need full circuit to save the final multiplexer in the library.
With necessary diagrams and equations, describe the operations of single-phase half –bridge and full-bridge inverters.
Draw the circuit diagram of 4-bit Ripple Carry Adder. Page 6 of 8
3. (a) The data sheet of a quad two-input AND gate (type 74S08) specifies the propagation delay and power supply parameters as Vcc = 5.0 V (typical), IcCH (for all four gates) = 18 mA, ICCL (for all four gates) = 32 mA, tpLH= 4.5 ns and tpHL = 5.0 ns. Determine the speed- power product specification. (b) Represent the following in the IEEE-754 floating-point standard using the single- precision format. (i) 32-bit binary number 11110000 11001100 10101010 00001111; (ii) (–118.625)10
1. Derive an equation for a 6 to 1 multiplexer. 2. Using the equation in (1), produce a gate network for the multiplexer. Use any gate seen in class.
7) The following figure shows a transistor-level (CMOS) circuit for some logic gate. Sketch the logic gate for the CMOS gate. Choices: a) NAND gate b) AND gate c) OR gate d) NOR gate
Question Vvv Draw the switching diagram for fifth harmonic elimination in a full-bridge inverter output voltage control scheme. Please be as descriptive as possible and thank you in advance.
1- What does the VoH parameter of a logic IC refer to? a) The highest permissible output voltage. b) The lowest output voltage recognized as logic 1. c) The highest output voltage recognized as logic 1. d) The highest output voltage recognized as logic 0.
Q4: Suggest a control gate drive circuit for a Triac, which is used to control a fan regulator. The gate signals should be synchronized with the input voltage. Draw the complete: 1. Circuit diagram with the load and 2. The waveform of the input and output voltages. ) Q.13 Indicate whether the following statements are correct or not then correct the incorrect statements 1) the multi pulse selected notching technique used in inverter is used to eliminate the low order harmonics and to reduce switching frequency, 2) In 3-phase half-controlled half-wave rectifier, the firing angle can be varied from 0 to 180 degrees while in 6-phase half-controlled half-wave rectifier can be varied from 0 to 150 degrees Q.14 Indicate whether the following statements are correct or not then correct the incorrect statements 1) In rectifier circuits, lower pulse number and connecting either primary or secondary of 3- phase winding in delta will reduce the harmonics content of the drawr. current 2) In…
Draw the Transistor Level Schematic for the following CMOS complex gates(Provide the answer with Picture diagram): a) Z= (A+B+C).D b) F = (AC) + B + (DE) c) Output = (A + B+C)(D+E)F d) 4 input NAND Gate e) 4 input NOR Gate