16. K1 and K2 are springs in parallel. They are attached in series to spring K3, which is attached in series to springs K4 and K5 which are in parallel. If K1=K2-K and K4=K5=2K and K3=0.5K, what is the equivalent spring constant?

16. K1 and K2 are springs in parallel. They are attached in series to spring K3, which is attached in series to springs K4 and K5 which are in parallel. If K1=K2-K and K4=K5=2K and K3=0.5K, what is the equivalent spring constant?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A helical compression spring is wound using 0.12-in-diameter phosphor-bronze B159 wire. The spring index C = 10 and the total number of coils is N = 14. You may assume that the spring has both ends squared and ground and is supported between fixed ends. Also, Sgy = 0.45 · Sut- a. Estimate the spring rate. b. Estimate the static load corresponding to the yield strength. c. What should the free length of the spring be to ensure that when it is compressed solid the torsional stress does not exceed the yield strength? d. Calculate the critical value of the free length of the spring to avoid buckling.
1. Design a compression helical spring to cary a load of 500 N with a deflection of 25 mm. The spring index may be taken as 8. Assume the following values for the spring material: Permissible shear stress 350 MPa Modulus of rigidity = 84 kN/mm2 4C – 1 + 4C – 4 0.615 Wahl's factor -, where C= spring index. [Ans. d= 5.893 mm; D=47.144 mm; n 6]
PROBLEM: 7 Calculate the dimensions of helical spring for a spring loaded safety valve from the following data : Valve Diameter = 45 mm; operating pressure = 0.6 N/mm2 Maximum pressure when the valve blows off freely = 0.99 N/mm2 ;valve lift when pressure rises from 0.6 to 0.99 N/mm2 = 5.5 mm ;Maximum permissible stress = 555 N/mm2 ; spring index ,C = 9; Modulus of rigidity =0.85x 105 N/mm2. Assume the spring coil is squared and ground.
The spring constant of a helical compression spring DOES NOT depend on "O+* 13/ coil diameter material strength t. number of active turns wire diameter
- Required information A helical compression spring is made of hard-drawn spring steel wire of diameter 0.0773in. and has an outside diameter of 0.85 in. The ends are plain and ground, and there are 8 coils. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the pitch of this spring? What force is needed to compress the spring to its solid length? Estimate the spring rate. The pitch of the spring is in. The force needed to compress the spring to its solid length is lbf. The spring rate is lbf/in.
Problem 4: A helical compression spring is to be cycled between 150 lbf and 300 lbf with a 1-in stroke. The number of cycles is low, so fatigue is not an issue. The coil must fit in a 2.1-in diameter hole with a 0.1-in clearance all the way around the spring. Use unpeened music wire with squared and ground ends. (a) Determine a suitable wire diameter, using a spring index of C = 7. (b) Determine a suitable mean coil diameter. (c) Determine the necessary spring constant. (d) Determine a suitable total number of coils. (e) Determine the necessary free length so that if the spring were compressed to its solid length, there would be no yielding
Required information A helical compression spring is wound using music wire of diameter, d, 2.16 mm. The spring has an outside diameter, OD, of 27 mm with plain ground ends and 14 coils. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What should be the free length to ensure that the torsional stress does not exceed the yield strength when the spring is compressed solid? What is the critical free length? Is there a possibility that the spring might buckle in service? The free length should be |mm. The critical free length should be Buckling is likely Eto occur. mm.
A typical compound helical spring consists of two coaxial closed coil spring having the following particulars: Outer spring 1: mean coil diameter = 100 mm Wire diameter = 12.5 mm No. of turns = 15 Inner spring 2: mean coil diameter = 75 mm No. of turns = 20Both the springs are of equal initial length when unloaded. Ifthe working stress for each spring is to be same. The modulus of rigidity for the wire material is 80 GPa. Calculate the following:a. Diameter of steel wire for inner spring. b. Stiffness of inner springc. Stiffness of the compound spring. I need answer ASAP. Thank you!
A typical compound helical spring consists of two coaxial closed coil spring having the following particulars: Outer spring 1: Mean coil diameter = 100mm Wire diameter = 12.5 mm No. of turns = 15 Inner spring 2: Mean coil diameter = 75 mm No. of turns = 20 Both the springs are of equal initial length when unloaded. If the working stress for each spring is to be the same. The modulus of rigidity for the wire material is 80 GPa. Calculate the following: a. Diameter of steel wire for inner spring b. Stiffness of inner spring c. Stiffness of the compound spring
A helical compression spring has a scale of 500 lb/in., an outside diameter of 2.75 in, a free length of 8 inches and with squared and ground ends. The load is 1,000 lbs and the working stress on the wire material is 65000 psi. If the Wahl factor of 1.25 is to be used, calculate the following: A. The standard wire diameter B. The number of active coil if G = 10 800 000 psi C. The solid height D. The stress at solid height
PROBLEM: 5 A helical valve spring is to be designed for an operating load range of 90N to 195N. The maximum deflection of the spring for this load range is 7.5 mm. Assuming a spring index of 9, a permissible shear stress of 550 N/mm2 for the material and the modulus of rigidity of 0.85x105 N/mm2. Determine the dimensions of the spring. (i.e. Diameter of the spring wire ,Mean coil diameter, Outer diameter of the spring, number of active turn and free length of the spring). Assume the spring coil is squared and ground.
A helical compression spring having 14 active coils is close coiled. It has a spring stiffness of 400lb/in. It is cut into two springs having 6 and 8 turns. Determine the spring stiffnesses of resulting springs.