The rigid bar AB shown below is supported by a steel rod AC having a diameter of d mm and a block. Ignore the weight of AB and AC. Consider the design of AC only, and the allowable stress for the steel in this application is = 160 MPa, and the load on AB is p = 14.2 kN/m. Calculate the desired diameter of AC: d = ___ mm (before you round up your answer to the nearest 1mm). Calculate your answer to 1 decimal place. The rigid bar AB shown below is supported by a steel rod AC having a diameter of d mm and a block. Ignore the weight of AB and AC. Consider the= 160 MPa, and the load on AB is p = 14.2 kN/m. Calculate thedesign of AC only, and the allowable stress for the steel in this application isdesired diameter of AC: d= mm (before you round up your answer to the nearest 1mm). Calculate your answer to 1 decimal place.(allow)pkN/m2 m

Answered: Image /qna-images/answer/1456c41e-72b2-4b6e-8e71-df826ebcc2b3.jpg

The rigid bar AB shown below is supported by a steel rod AC having a diameter of d mm and a block. Ignore the weight of AB and AC. Consider the design of AC only, and the allowable stress for the steel in this application is = 160 MPa, and the load on AB is p = 14.2 kN/m. Calculate the (allow) desired diameter of AC: d = mm (before you round up your answer to the nearest 1mm). Calculate your answer to 1 decimal place. pkN/m 2m B

The rigid bar AB shown below is supported by a steel rod AC having a diameter of d mm and a block. Ignore the weight of AB and AC. Consider the design of AC only, and the allowable stress for the steel in this application is = 160 MPa, and the load on AB is p = 14.2 kN/m. Calculate the (allow) desired diameter of AC: d = mm (before you round up your answer to the nearest 1mm). Calculate your answer to 1 decimal place. pkN/m 2m B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.4.19P: A horizontal rigid bar of weight If' = 72001b is supported by three slender circular rods that are...

See similar textbooks

Similar questions

A flat bar of width b and thickness t has a hole of diameter d drilled through it (see figure). The hole may have any diameter that will fit within the bar. What is the maximum permissible tensile load Pmaxif the allowable tensile stress in the material is st?
A bar of monel metal with a length L = 9 in. and a diameter d = 0225 in. is loaded axially by a tensile force P (see figure). If the bar elongates by 0.0)95 in., what is the decrease in diameter
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A vertical bar is loaded with axial loads at points B, C, and D. as shown in the figure. The bar is made of steel with a modulus of elasticity E = 29,000 ksi., The bar has a cross-sectional area of 8.24 in2. Calculate the displacements at points B, C, and D. Ignore the weight of the bar
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
,10-6 A prismatic bar with a diameter d0= 20 mm is being compared with a stepped bar of the same diameter(d| = 20 mm) that is enlarged in the middle region lo a diameter d2= 25 mm (see figure). The radius of the fillets in the stepped bar is 2.0 mm. (a) Does enlarging the bar in the middle region make it stronger than the prismatic bar? Demonstrate your answer by determining the maximum permissible load for the prismatic bar and the maximum permissible load F, for the enlarged bar, assuming that the allowable stress for the material is 80 MPa. (b) What should be the diameter d0of the prismatic bar if it is to have the same maximum permissible load as does the stepped bar?
An aluminum tube is required to transmit an axial tensile force P = 33 k (sec figure part a). The thickness of the wall of the tube is 0.25 in. (a) What is the minimum required outer diameter d minif the allowable tensile stress is 12.000 psi? (b) Repeat part (a) if the tube has a hole of a diameter J/10 at mid-length (see figure parts b and C).
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
Two bars AC and BC of the same material support a vertical load P (see figure). The length L of the horizontal bar is fixed, but the angle fl can be varied by moving support A vertically and changing the length of bar AC to correspond with the new position of support A. The allowable stresses in the bars are the same in tension and compression. When the angle ft is reduced, bar AC becomes shorter, but the cross-sectional areas of both bars increase because the axial forces are larger. The opposite effects occur if the angle 0 is increased. Thus, the weight of the structure (which is proportional to the volume) depends upon the angle ft. Determine the angle ft so that the structure has minimum weight without exceeding the allowable stresses in the bars. Note: The weights of the bars are very small compared to the force P and may be disregarded.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.