12.31 Abalanced delta-connected load is supplied by a 60-Hz three-phase source with a line voltage of 240 V. Each load phase draws 6 kW at a lagging power factor of 0.8. Find: (a) the load impedance per phase (b) the line current (c) the value of capacitance needed to be connected in parallel with each load phase to minimize the current from the source

12.31 Abalanced delta-connected load is supplied by a 60-Hz three-phase source with a line voltage of 240 V. Each load phase draws 6 kW at a lagging power factor of 0.8. Find: (a) the load impedance per phase (b) the line current (c) the value of capacitance needed to be connected in parallel with each load phase to minimize the current from the source

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
)Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2 kV and frequency 60 Hz. The first load has a power of 50 kVA and a factor of rear power of 0.9. The second charge has a power of 45 kW and a rear power factorof 0.91. Determine in steady state the kVAR power and the capacity required to correct the Total power factor to a value of 0.97 rear.
There is an installation with two equal triphasic loads of 300 kVA each and a power factor of 0.9 lagging. When connecting a pure reactive element in parallel, the reactive power at the entrance of the installation is 150 kVARS, with a lagging power factor. We can say that: a) A bank of reactors was connected and the fp deteriorated. b) A capacitor bank was connected and the pf deteriorated. c) A bank of reactors was connected and the fp improved. d) A capacitor bank was connected and the pf improved. e) None of the above
lši vl pir:10 Expert Q&A + 1. For the circuit in Figure: a. Determine I, VR, and Ve in phasor form. b. Calculate the total power factor, and indicate whether it is leading or lagging. c. Calculate the average power delivered to the circuit. d. Draw the impedance diagram. e. Find the voltages VR and Vcusing the voltage divider rule and compare them with the results of part(a) above. + Uc - + Ug - 30 2 L = 0.2 H L =0.2 H C = 4 µF e = V2(20) sin(377t + 40°) Expert Answer Home Search More II
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
low voltage systems In the reverse phase, a 1000 kw powerful load under 0.5 power factor is fed from a 5 kv source.A capacitor is connected in parallel with the load to increase the power factor to 0.8. a-) Find the required capacitor power. b-) Compare the apparent power before and after compensation.
The values of the elements for the given circuit are given below.The maximum average power that can be transferred to the ZL load iswhich one?R1 = 400 OhmsL = 1000j OhmsR2 = 500 Ohms
Three Impedances each of (9 - j18)N are connected in mesh across a three-phase 415V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip) Line current real power reactive power
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
Two impedances are connected in parallel to the supply, the first takes a current of 40 A at a lagging phase angle of 30°, and the second a current of 30 A at a leading phase angle of 45°. Draw a phasor diagram to scale to represent the supply voltage and these currents. From this diagram, by construction, determine the total current taken from the supply and its phase angle.