1 and 2 are connected. Number 1 is already posted in thus page. Please answer. Neglect the simulation thing. I only need the solution. 1.) A 60 Hz, 230 mile, three-phase overhead transmission line has a seriesimpedance of o.8431 cis(79.04°) N/mi and a shunt admittance y =5.105 x 10-6 cis(90°) S/mi. The load at the receiving end is 125 MW atunity power factor and at 215 kV. Find the voltage regulation of theline. Simulate in Power World and show the voltage at full load and noload.%3D 2.) Given the uncompensated line of #1, let a three-phase shunt reactor(inductor) that compensates for (A) 70%; (B) 50%; and (C) 30% of thetotal shunt admittance of the line be connected at the receiving end ofthe line during no-load conditions. Determine the effect of voltageregulation with the reactor connected at no load. Assume that thereactor is removed under full-load conditions. Plot the graph ofcompensation of shunt reactor and voltage at no load. Simulate also inPower World.

As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again.

A 60 Hz, 230 mile, three-phase overhead transmission line has a series impedance of o.8431 cis(79.04°) N/mi and a shunt admittance y = 5.105 x 10-6 cis(90°) S/mi. The load at the receiving end is 125 MW at unity power factor and at 215 kV. Find the voltage regulation of the line. Simulate in Power World and show the voltage at full load and no load.

A 60 Hz, 230 mile, three-phase overhead transmission line has a series impedance of o.8431 cis(79.04°) N/mi and a shunt admittance y = 5.105 x 10-6 cis(90°) S/mi. The load at the receiving end is 125 MW at unity power factor and at 215 kV. Find the voltage regulation of the line. Simulate in Power World and show the voltage at full load and no load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.41P

See similar textbooks

Similar questions

Problem 4- A large 3-phase industrial load draws 3.6 MVA at 0.85 power factor lagging from through a three- phase 12.47/7.2 kV 3-wire overhead distribution line. The phase conductor is #1 ACSR “Robin". Taking 3.6 MVA and 12.47 kV as base values, determine (a) The base impedance in (N) (b) The reactive power drawn by the load (p.u.) (c) The total current (p.u.) drawn from the power supply
Paragraph Styles The power factor must be close to in the transmission lines will be reduced To insure that losses D(Ctrl) -
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
What do you understand by means of power system? A 3-p, 50 Hz transmission [ line is 120 km long. It has a per phase series impedance of 0.05+j0.45 2 per km and a per phase shunt admittance of j3.4*10-6 S per km. It delivers 200 MW load at 220 kV with 80% power factor lagging. Find the voltage regulation and transmission efficiency.
The 13.2 kV 50-Hz generator feeds a load over a line with (Zload) impedance Zline. Load is 800n + j500n and impedance of the line is 20 + j300 a) If the generator is directly connected to the load as given in (a), what will be the line losses? b) If the generator is connected to the load using step-up and step-down transformers as given in (b), what will be the line losses? c) How much is the increase in efficiency compared to (a) from (b)? Zline 2. (a) 1:10 10:1 Zline Tr Tr2 (b) Zload Zload
1) A 60-Hz, ...-km, three-phase overhead transmission line has a series impedance z = 0.8431L79.04 ohm/km and a shunt admittance y = 5.105 × 106 L90 S/km. The load at the receiving end is 125 MW at unity power factor and at 215 KVLL. Determine the voltage, current, real and reactive power at the sending end and the percent voltage regulation of the line for nominal pi network. (Please determine the length of the transmission line within the specified limits: 150-220 km. By considering the length value you determined yourself, solve the question.)
The impedance per phase of a 3-phase transmission line on a base of 100 MVA and 100 kV is 2 p.u. The value of this impedance on a base of 400 MVA and 400 kV would be?
A three-phase balanced load of 15A per phase is supplied by a steel wire armoured cable with a c.s.a. of 2.5mm². The voltage drop for this cable is 15mv/A/m and the circuit is 40m long. Calculate the voltage drop in the cable.
of stion 4 A single phase transmission line is delivering 450 kVA load at 12 kV. Its resistance is 4.5 2 and inductive reactance is 6 2. If the load power factor is 0.9 lagging. Determine the Current through the line Sending end voltage Sending end power factor Regulation of transmission line Efficiency of transmission line A load of 120 MW at a power factor of 0.8 lagging can be delivered by a 3-phase transmission line. The voltage at the intained at 33 kV and the loss in the transmission as 7.5 % of the power delivered. (Consider
Power in a three phase delta system with balanced load is equal to (Sqrt (3)) (VL) (IL) (p.f.) (Sqrt (3)) (Vph) (Iph) (p.f.) (Sqrt (3)) (VL) (Iph) (p.f.) O (Sqrt (3)) (Vph) (IL) (p.f.)
One circuit of a single-phase transmission line is composed of three solid 0.12" radius wires. The return circuit is composed of two 0.15" radius wires. Find the inductance of the complete line in mH/mi. The distance between wires are 40" horizontally and 25" vertically. A. 2.54 mH/mi B. 2.478 mH/mi C. 2.488 mH/mi D. 2.567 mH/mi Provide Clear Explaination