11.19 Figure 11.35a shows a pile. Let L = H = 4 m, yau = 17.5 kN/m³, and d'ral = 25°. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that 8' = 0,5bau. 20 m, D (pile diameter) = 450 mm, fill

11.19 Figure 11.35a shows a pile. Let L = H = 4 m, yau = 17.5 kN/m³, and d'ral = 25°. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that 8' = 0,5bau. 20 m, D (pile diameter) = 450 mm, fill

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.20P: Figure 18.26a shows a pile. Let L = 20 m, D = 450 mm. Hf = 4m, f = 17.5 kN/m3, fill = 25. Determine...

See similar textbooks

Related questions

Q: A rectangular pile (0.5 x 0.5 m.) is driven in a clayey soil arrangement composed of two different…

A: Please refer the attached image for complete solution. THANK YOU.

Q: Q4) For the pile-soil system shown in Fig. (4), estimate the required pile length to carry an…

A: Given Data:Load = 24kN.For dense sandγsat=21kN/m3ϕ=40°ks=1.5

Q: For the figure shown if the pile length is 15 m Find the factor of safety (Fs), if the allowable…

Q: The wooden pile shown in the figure has a diameter of 90 mm and is subjected to a load of P = 60 kN.…

Q: A rectangular pile (0.67 x 0.5 m.) is driven in a clayey soil arrangement composed of two different…

Q: For the sheet pile wall shown in figure below, find 1- Quantity of seepage (k= 0. 5 * 10-3 m/sec) 2-…

A: Given: k=0.5×10-3 m/sec H=3 m No. of flow channels, Nf=5 No. of potential drops, Nd=11

Q: 2. Consider a group of 450 mm x 450 mm reinforced concrete piles were driven into thick loose sand…

A: Given data, size of pile=450 mmx 450mm unit weight of loose sand soil,γ=16 kN/m3 Internel friction…

Q: A square concrete pile12m long is shown in Figure. Estimate the following: Ultimate shaft carrying…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: Н.О 10 A concrete pile 20 m long having a cross section of 0.46 m x 0.46 m is fully embedded in a…

A: Given data- Saturated Clay layer. Length of concrete pile (L) = 20 m Square cross-section = 0.46 m ×…

Q: 04: Calculate the allowable axial load for the driven pile of ( 0.5 m ) dia. And ( 20 m) depth, in a…

Q: A 30 m long concrete pile is 305 mm times 350 mm in cross section and is fully embedded in a sand…

A: Solution Given data length= 30 m cross section= 305mm*350 mm FOS= 2 ϕ= 300 fy= 21 MPa γ= 16 KN/m3

Q: The plan of a group pile is shown in the figure. Assume that the piles are embedded in a saturated…

A: Given Data Diameter of piles (D)=316 mm, center-to-center spacing of piles=600 mm, and length of…

Q: Refer to Figure 9.42b. Let L = 18 m, γfill = 17 kN/m3, γsat(clay) = 19.8 kN/m3, Φ'clay = 20°, Hf =…

A: The downward drag force will be: Qn=pK'yf Hf tanδ'L1+L12pK'y'tanδ'2 ...(1)The neutral…

Q: Sheet pile k= 4 x 10-4 cm/sec Impermeable layer Figure 8.23 8.2 Draw a flow net for the single row…

A: Given:- The value of k = 4×10-4 cm/sec The value of H1 = 3 m The value of H2 = 0.5 m The value of D…

Q: Refer to the pile shown in Figure P 9.1. Estimate the side resistance Qs bya. Using Eqs. (9.40)…

A: Coyle and Castello analyzed 24 large–scale field load tests of driven piles in sand. from the basis…

Q: A 600mm diameter pile is embedded in 3 layers of dense sand at a depth of 17m. Nq = 86. The…

Q: A circular pile with a diameter of 400 mm was driven to a depth of 12 meters into the normally…

Q: For the pile distribution below, determine the load Pp that the red pile will receive, in Ton. P=254…

A: given:d= 2 mex=0.2 mey=0.3 mH=1.3 mP=254 ton

Q: An excavation 5 m depth is supported by a sheet pile. The sheet pile is extended 3.2 m below the…

Q: A circular pile having a diameter of 0.33 m is 14.21 m long which is embedded in a layer of dense…

Q: A driven closed-ended pile, circular in cross section, is show in below figure P10. Calculate the…

A: Since you have asked multiple question, we will solve the first question for you and with multiple…

Q: The section of a sheet pile is shown in the figure. The coefficient of permeability of the soil is…

Q: Redo Problem 9.23 assuming that the water table coincides with the top of the fill and that…

A: Solution Calculate the total downward drag force or negative skin friction using the following…

Q: Figure P14.1 shows a cantilever sheet-pile wall penetrating a granular soil. Here, L = 4 m, L2 = 8…

A: Sheet piles are metal parts with interlocking edges driven into the ground to provide permanent or…

Q: (b) A single test pile, 300 mm diameter, is driven through a depth of 8 m of clay which has an…

Q: A 20-m-long concrete pile is shown in Figure P9.1. Estimate the ultimate point load Qp bya.…

A: Given:- ∅'2=42γ=18.5kN/m3Concrete pile=460 x 460mmLoose sand:-∅'1=30 degreeγ=18.6kN/m3 L=20m To…

Q: P5.14 The wooden pile shown in the figure has a diameter of 100 mm and subjected to a load of P =…

A: Given ; Dia of wooden pile = 100 mm P = 75kN Frictional resistance w = 3.70 kN/m Length of pile -…

Q: Redo Problem 9.27 with the following: center-to-center spacing of piles 5 30 in., length of piles =…

A: Solution: Calculate ultimate bearing capacity of piles acting individually by using the…

Q: P-3 Refer to Figure, for which L, = 2.4 m, Sand L2 = 4.6 m, y = 15.7 kN/m³, Ysat = 17.3 kN/m³, and…

Q: A driven closed-ended pile, circular in cross section, is shown in Figure P 9.4.Calculate the…

A: Given:- Irr = 50. c'=0 width =381mm To find:- a. The ultimate point load using Meyerhof’s…

Q: A steel pipe pile of 61 cm outside diameter with a wall thickness of 2.5 cm is driven into loose…

Q: For the (4 x 4) pile group as shown in the figure, the settlement of pile group, in a normally…

Q: A concrete pile 20 m long having a cross section of 0.46 m x 0.46 m is fully embedded in a saturated…

Q: Qó: For anchor sheet pile in sandy soll as shown in Figure below, Find the following: y=16 kN/m ka=…

A: The wall given is : The given wall is an anchored sheet pile wall.

Q: Determine the diameter of 70 ft long pile driven in the medium dense sand (Shown in Figure). Design…

Q: Determine the primary consolidation settlement for the 20 m long pile group shown below. Soil…

Q: A 12 m long concrete pile is shown in Figure P11.1. Estimate the ultimate point load Q, by a.…

A: Using Vesic's method, shear failure surfaces are slightly more accurate, and the Terzaghi method is…

Q: A 600mm diameter pile is embedded in 3 layers of dense sand at a depth of 17m. Nq = 86. The…

A: Given, Nq = 86 D = 600 mm or 0.6 m

Q: Khosla's Theory Example (2.6): H.W. An impervious floor of a weir on permeable soil is 16 m long and…

A: Introduction- Khosla's Theory- Water seepage does not crawl along the bottom contour, according to…

Q: 3. A 10.75 cm diameter steel pile is driven 25 m into stiff, insensitive clay. The pile has an…

A: Diameter of pile (d) = 10.75 cm = 0.1075 m Length of the pile (l) = 25 m Friction capacity (fs) =…

Q: 11.2 Refer to the pile shown in Figure P11.1. Estimate the side resistance Q, by a. Using Eqs.…

Q: The wooden pile shown in the figure has a diameter of 100 mm and is subjected to a load of P = 70…

A: This question is related to the Strength of Material.

Q: A driven closed-ended pile, circular in cross section, is shown in Figure P9.4. Calculate the…

A: Ultimate point load is calculated by the following formula: Qb=σv'NqAbwhere Ab=area of pile =…

Q: The wooden pile shown in the figure has a diameter of 95 mm and is subjected to a load of P = 80 kN.…

A: Given P= 80 KN Dia of pile = 95 mm

Q: The wooden pile shown in the figure has a diameter of 105 mm and is subjected to a load of P = 70…

Q: Determine the factor of safety against heave on the downstream side of the single-row sheet pile…

Q: Problem #1 The figure below shows a cantilever sheet-pile wall penetrating a granular soil. Here,…

Q: 12.2 A 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Q, by a.…

A: Concrete pile : Reinforced cement concrete piles are a structural element of a deep foundation that…

Q: Consider a 15 m long concrete pile with a cross section of 0.45 m x 0.45 m fully embedded in sand.…

A: Meyerhof (1963) proposed a recipe for computation of bearing limit like the one proposed by Terzaghi…

Q: G.W.T. Clay C, = 50.3 kN/m² Ysat = 17.6 kN/m³ 4.57 m Clay C, = 85.1 kN/m² Ysat = 19.02 kN/m³ 13.72…

Concept explainers

Temperature as a Fundamental Dimension

There are certain rules to write dimensions of a physical quantity using the fundamental dimensions. They are outlined below.

Question

Please answer 11.19

(Answer)

25.3kN

11.19 Figure 11.35a shows a pile. Let L = 20 m, D (pile diameter) = 450 mm,
H, = 4 m, Ya = 17.5 kN/m², and d'al
= 25°. Determine the total downward
drag force on the pile. Assume that the fill is located above the water table and
that 8' = 0.54-

Clay Hf
fill
Sand
(a)
Figure 11.35 Negative skin friction

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
Refer to the pile shown in Figure P 9.1. Estimate the side resistance Qs bya. Using Eqs. (9.40) through (9.42). Use K = 1.5 and ẟ' = 0.6 Φ'b. Coyle and Castello’s method [Eq. (9.44)]
For the pile distribution below, determine the load Pp that the red pile will receive, in Ton. P = 254 Ton, d = 2 m, ex = 0.2 m, ey = 0.3 m, H = 1.3 m. ex, e and positive with the axes. Consider the self-weight of the head. O O O +2/2+0+0+0/2+ d/2
A concrete bored pile has a diameter of 800 mm as given in the figure below. Calculate the ultimate load carrying capacity of the pile. -0.8- Clay Cu = 60 kN/m² Y = 18 kN/m³ %3D 4m G.W.T Sand 6m $ = 30° Y = 20 kN/m³ Clay Cu = 100 kN/m² Y = 20 kN/m³ 5m
QUESTION 5 Calculate the load bearing capacity of the pile shown in Figure Q5. Assume that it is a bored pile, and state other assumptions made. 0.6 m Firm Clay Y. = 18KN/m2 = 40 kPa 3m Stiff Clay Y, = 19kN/m³ Cu = 110 kPa 2.5m WT 13m Dense Gravel Y. = 21kN/m² o' = 37° 15m Figure Q5
6) A 2-ft x 2-ft square concrete pile is shown. Ignore the resistance of the soft clay. Assume Na 10. For a safety factor of 3.0, the allowable load capacity of the pile is most nearly: a. 344 kips b. 169 kips c. 128 kips d. 225 kips 5 ft 30 ft R SOFT CLAY y=120 pcf SAND Y = 115 pcf =32°
Consider a drilled, rough concrete pile with diameter B = 1m and length D = 10m embedded in a site underlain by a 5m thick layer of sand with fiction angle = 41 degrees and Ko = 0.5 that lies over an 8m thick layer of clay with fiction angle = 36 degrees, Ko = 0.38, and Su = 70 kPa. a. Determine the long term end bearing capacity of the pile. b. Determine the long term capacity of the pile.
Find the maximum pile capacity for the pile group shown in figure below. If My = 500 kN.m and V = 7200 kN. 'My X=1.4 - x=1.4- y=1.2 y=1.2
The section of a 3 x 4 group pile in a layered saturated clay is shown in the figure below. The piles are square in cross section (356 mm x 356 mm). The center-to-center spacing, d, of the piles is 889 mm. Determine the allowable load-bearing capacity of the pile group. Use FS = 4. Note that the groundwater table coincides with the ground surface.
Steps Consider a precast concrete pile that is 0.505 m X 0.505 m in cross section driven in a homogeneous sand with y = 17 kN/m² and friction angle $ = 33ª . The pile is 9 m long. Use Meyerhof's methods for estimating the frictional resistance Qs in Sand. Show all calculation steps. Depth below ground surface (m) 1.5 3.0 4.5 6.0 7.5 9.0 10.5 12.0 13.5 15.0 16.5 18.0 19.5 21.0 Noo 8 10 9 12 14 18 17 20 28 29 32 30 27
A bored pile is shown in the figure. The diameter of the pile is 60 cm. Calculate the ultimate bearing capacity of the pile. Assume Dor=20x), the pile soil motion angle, 8=0.75*8' Sand c'=0, 0-30° 10m 8=20 kN/m Clay Cu = 100kpa X=20kN/m3 5m
Please round to the nearest Hundredth (i.e., 0.01). No Comma! A square pile, 21 m long is driven into a homogeneous sand layer. The pile's width (diameter) is 0.4m. The standard penetration resistance near the vicinity of the pile is 12. Calculate the ultimate skin friction force (Qs) of the pile. Use Briaud & Tucker method. Hint: Qs = fs x As Qs = kN