For the figure shown if the pile length is 15 m Find the factor of safety (Fs), if the allowable carried load 255 kN and the pile cross section (0.3 x 0.3) m Clay 15 m Cu = 20 kPa Øu = 0 a = 1 ysat = 20 kN/m³ Sand Ø = 30 Nq = 30 for Janbus method %3D

For the figure shown if the pile length is 15 m Find the factor of safety (Fs), if the allowable carried load 255 kN and the pile cross section (0.3 x 0.3) m Clay 15 m Cu = 20 kPa Øu = 0 a = 1 ysat = 20 kN/m³ Sand Ø = 30 Nq = 30 for Janbus method %3D

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.8P: Consider a 500 mm diameter pile having a length of 18 m in a clay. Given: γ = 20.0 kN/m3 and cu = 60...

See similar textbooks

Similar questions

Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
A steel pile (H-section; HP 360 1.491; see Table 18.1) is driven into a layer of sandstone The length of the pile is 18.9 m. Following are the properties of the sandstone: Unconfined compression strength = qu(lab) = 78.7 MN/m2 Angle of friction = 36 Using a factor of safety of 3, estimate the allowable point load that can be carried by the pile. Use Eq. (18.42).
Redo Problem 12.3 using Coyle and Castellos methods for estimating both Qp and Qs. 12.3 A 500 mm diameter and 20 m long concrete pile is driven into a sand where = 18.5 kN/m3 and = 32. Assuming = 0.7 and K = 1.5 Ko, determine the load-carrying capacity of the pile, with a factor of safety of 3. Use Meyerhofs method [Eq. (12.18)] for computing the point load-carrying capacity Qp, and Eqs. (12.42) and (12.43) for computing the load-carrying capacity of the pile shaft Qs.
Calculate the pile's allowable bearing load using the corrected SPT values at various depths given in the figure below (factor of safety is 1.5). 10m D=1m 2m 2m 2m 2m 2m SPT1=14. SPT2=16 SPT3=18. SPT4=18 -- SPT5=20. Corrected SPT Values
for pile shown in fig. below, Sind Qu дозжазт 3m XX =30 S=0.84 Sang XXX Ks=1+3 = 16 kN m. 꽃 Q=36 Sand G= 0.74 ks = 104 85-4 1711. m clay си=50 кра 207 Xead = 18 KN 3 Q2 * Qu=Ap 4 Qb = AP (CNC + BV₂NH j +0.5XD NY 5m • Q₁ = {(ca + ks Sv tand *As L=1 ۲/۵ 12m BAZAT CHEES
Determine load carrying capacity of pile without considering critical depth concept. Diameter of pile 0.4 m.Ng =132 for o = 40° to m y 4.b Cot-opf "loose Sand K=1 = 21-15 From. 8a 19 Cu 20k Demse Sund 2 20 $=40° K=2 -I 30°
13) A cylindrical pile of diameter 0.3 m is driven to a depth of 15 m in to an NC clay as shown in the figure below. Using the factor of safety of 3, the allowable load capacity of the pile using the a-method is most nearly: a. 426 kN b. 178 kN c. 330 kN d. 105 kN 10 m 5 m Gy=25k9x 7-15998 C₂#100 kPa p=0 1*17k9*
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425KN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C; = 0.09, ơ'o = 150kN/m? At 10m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 225KN/m? At 12m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 300KN/m? 7m 5m Clay 3 10m Unit weight = 18KN/m Friction angle = 0 degree 2 Cohesion = 100KN/m Figure 1: Pile system
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425KN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C, = 0.09, ơ'o = 150KN/m? At 10m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 225KN/m? At 12m, e, = 0.55, Cc = 0.32, C, = 0.09, oo = 300KN/m? 7m 5m Clay 10m Unit weight = 18kN/m Friction angle = 0 degree Cohesion = 100KN/m
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425kN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 150kN/m? At 10m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 225kN/m2 %3D At 12m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 300KN/m2 %3D 7m 5m Clay 3 10m Unit weight = 18KN/m %3D Friction angle = 0 degree 2 Cohesion = 100KN/m
b) A bored pile was installed in dense sand with the following data: Diameter of pile 600 mm, length of pile= 20 m of internal friction () = 30°, 1=20 kN/m The ground water table was at a depth of 6 m. below the ground surface. Assuming factor of safety of 3 calculate the estimated safe load capacity of a single pile. %3D
Compute the compressive force at the most stressed pile for each pile cap given in the table below. All column loads are unfactored and acting at the pile group centroid unless noted otherwise. My LL My (kN*m) y Pile Cap DL (kN)* LL(kN) LL Mx (kN*m) PC-1 1800 300 400 350 PC-2 1800 300 400 350 Mx *Pile cap weight is not included in the DL Notes: Pile diameter=600mm Use a pile cap thickness of 450mm for all cases with a conc unit wt of 23.5kN/m? PC-1 РС-2 3600 3600 1800 1800 1200 000 0081 009S