1. Caused by ane or more cells not producing voltage. May be due to cheap construction, overheating or mechanical damage. A. Loss of active materials B. Internal Shorts C. Sullation D. Internal Corrosion 2. Result of excessive depth of discharge and age. Mostly a probiem with cheaper batleries. A. Loss of active materials B. Internal Shorts C. Sulfalion D. Internal Corosion 3. The unit of measurement used for electrical pressure is- A. ohm B. volt C. energy D. amperes

1. Caused by ane or more cells not producing voltage. May be due to cheap construction, overheating or mechanical damage. A. Loss of active materials B. Internal Shorts C. Sullation D. Internal Corrosion 2. Result of excessive depth of discharge and age. Mostly a probiem with cheaper batleries. A. Loss of active materials B. Internal Shorts C. Sulfalion D. Internal Corosion 3. The unit of measurement used for electrical pressure is- A. ohm B. volt C. energy D. amperes

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Shackle type insulators are used for voltage in the order of ....................... Complete the answer
Two silicon diodes are connected in parallel and in series with resistor 0.33kohms and a battery of 10V. the voltage across the resistor 0.33k ohms is ___. The current flowing through resistor 0.33K ohms is approximately equal to___. The current of one diode is___.
1- A). Which of the following could be used as a discharge device in an inductive AC circuit? a) resistor b) diode c) metal oxide varistor d) "a" and "c", not "b" B. What is the purpose of a discharge device used in conjunction with opening a highly inductive circuit? a) to minimize the possibility of damage to the circuits insulation as a result of a high induced voltage b) to minimize the possibility of endangering the life of the person opening the controlling switch c) to allow the magnetic field to gradually collapse, thus limiting the value of the self-induced ernf d) all of the above C. The high voltage induced by an inductor when its circuit is opened could be used constructively for a) an automotive ignition system b) an electric fence c) both "a" and "b" d) neither "a" nor "b"
(03) AC Diode circuits. (Course: Electronic Devices and Circuit Theory) -Redraw the circuit, Assume diodes are off and Redraw, Apply KVL. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.
The purpose of the current limiting resistor in a Zener diode circuit is to _________. a. Maintain a constant current through the load resistor b. Maintain a constant voltage across the Zener diode c. Maintain a constant current through the Zener diode d. Drop the additional voltage from the power supply in order to maintain a constant voltage across the Zener diode Please answer it clearly.
1. The reverse bias diodes a. D1 only b. D2 only c. Everything d. None 2. The close circuit is a. R1 and D1 side only b. R2 and D2 side only c. Everything d. None
what are charging and discharging time of this circuit.
Summarize on how testing is carried out on isolators and circuit breakers of high voltage system. High voltage engineering
6. It is the minimum anode current required for an SCR to maintain conduction. a. Breakover Voltage b. Holding Current c. Break Back Voltage d. Leakage Current 7. It is the simplest thyristor. a. SUS b. SBS c. SCR d. DIAC 8. It operates like two diodes connected in inverse parallel. a. SUS b. SBS c. SCR d. DIAC 9. The three terminals of an SCR are a. E,B,C b. A,K c. A,K,G d. MT1,MT,G 10. When an SCR is turned on, the anode to cathode voltage is approximately a. 6 V b. 0.7 V c. 0 V d. none of these
Define corrosion and also explain primary and secondary briefly explanation? step by step
Which change to the circuit will not extend the charging time of one time constant.a. Increasing the value of the capacitorb. Increasing the value of the resistorc. Increasing the voltage from 15 to 20 volts
Semiconductor components such as diodes and transistors are easily damaged by the high temperatures of soldering, so care must be taken to protect these components during the soldering process. One way to do this is to use a heat sink to draw heat away from the component without cooling the connection point too much. Heat sinks made out of sheet metal may be temporarily clipped to the component leads, one at a time, to prevent the solder's high temperature from thermally conducting all the way to the component body: In the absence of a formal heat sink, can you think of any ways to fashion your own ïmpromptu" heat sinks out of commonly available tools and/or objects?