1. A sinusoidal voltage source in placed in series with a DC voltage source and produces an output of: v(t)= 70.7cos(377t) + 20 volts [ 70.7 = 50√2] Calculate: a. v²(t) b. Vrms c. The magnitude of the RMS current if the combined source is placed across a load of Z=4+j3 ohms (if you have trouble with part b, just assume a voltage of 100 Vrms for part c)

1. A sinusoidal voltage source in placed in series with a DC voltage source and produces an output of: v(t)= 70.7cos(377t) + 20 volts [ 70.7 = 50√2] Calculate: a. v²(t) b. Vrms c. The magnitude of the RMS current if the combined source is placed across a load of Z=4+j3 ohms (if you have trouble with part b, just assume a voltage of 100 Vrms for part c)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequeney of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms . (iii) Determine phase relationship between voltage and current waveform.
1. Instruction: Provide the correct answer. 1. What is the relationship between the supply voltage and circuit current in purely capacitive circuits?. 2. Vm = 100cos(377t + 75°) transform into sine form is a complex number that represents the amplitude and phase of a sinusoid. 3. 4. What is the phase relationship between a supply voltage and current through a purely inductive circuit?. 5. The rms value of the signal is also called the 6. The It is also the cosine of the angle of the load impedance. 7. When Q < 0, the power factor is 8. The process of increasing the power factor without altering the voltage or current to the original load is known as 9. is the cosine of the phase difference between voltage and current. is the measurement to measure average power. 10. What is the meaning of VAR?
The single phase AC sinusoidal voltage then the rms value of the voltage v is .........
For the phasor diagram in figure 6 express the voltages in sinusoids for a period of 5ms. Im Re )e,=45° e,=20 Vz=10 V2=8 Figure 7 a. Va(t)=. b. V2(t)=. c. What is the rms voltage of V1 = d. What is the rms voltage of V2=_ e. What is the frequency in Hz = f. What is the angular frequency =. In terms of lagging and leading what is the exact phase relationship between V, (t) and V2(t) g.
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
Instruction: Provide the correct answer. 1. What is the relationship between the supply voltage and circuit current in purely capacitive circuits? 2. Vm = 100cos(377t + 75°) transform into sine form is a complex number that represents the amplitude and phase of a sinusoid. 3. 4. What is the phase relationship between a supply voltage and current through a purely inductive circuit? . 5. The rms value of the signal is also called the
The output voltage waveform of a four quadrant chopper is shown in figure. In the waveform, Vdc is input voltage, D is duty cycle ratio and T is cycle time. DT T. The RMS value of ripple component in output voltage is (A) Vác 2V VD-D (В) V(2D-1) (C) de de (D) V de VD- D? yd
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor