1- The driver's foot can apply 400 lbf force to the brake pedal. Given that area of blue piston in the Master Cylinderis about 5 in?:a) Calculate the pressure in the master cylinder.b) What is the pressure in the "Rear wheel cylinder pistons"?c) If the area of pistons in the "Rear wheel cylinder pistons" is 25in?, how much force those pistons areapplying against the pads?Brake pedalMastercylinderBrakelinesFrontbrakePadscalipersRear wheelcylinderpistonsPadsRotor

To find: (a) The pressure in the master cylinder. (b) The pressure in the "Rear wheel cylinder…

1- The driver's foot can apply 400 lbf force to the brake pedal. Given that area of blue piston in the Master Cylinder is about 5 in²: a) Calculate the pressure in the master cylinder. b) c) What is the pressure in the "Rear wheel cylinder pistons"? If the area of pistons in the "Rear wheel cylinder pistons" is 25in², how much force those pistons are applying against the pads? Pads Master cylinder Front brake calipers Brake lines Rear wheel cylinder pistons Rotor Brake pedal Pads

1- The driver's foot can apply 400 lbf force to the brake pedal. Given that area of blue piston in the Master Cylinder is about 5 in²: a) Calculate the pressure in the master cylinder. b) c) What is the pressure in the "Rear wheel cylinder pistons"? If the area of pistons in the "Rear wheel cylinder pistons" is 25in², how much force those pistons are applying against the pads? Pads Master cylinder Front brake calipers Brake lines Rear wheel cylinder pistons Rotor Brake pedal Pads

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter6: Milling

Section6.1: Introduction To The Vertical Milling Machine

Problem 2RQ: Briefly describe the direction of movement provided by the saddle.

See similar textbooks

Similar questions

What is the force member in LC1 in N?
A hydraulic press must be used to press-fit two components together in an assembly process. The system must generate at least 975 lb of force to perform the press fit. The piston at the input cylinder is pushed with a force of 250 lb and has an area of 30 in.2. The output can use up to 15 cylinders that are each 30 in.2. How much mechanical advantage is required to gain the necessary force ?
1-The magnitude of N2 (normal force on Surface-2) is _____N 2-The magnitude of F2 (friction force on Surface-2) is _____N. 3- Consider the FBD of the Wedge: The direction of N2 (normal force on Surface-2) is _____degrees. Please need help. use that fig to respond to questions 1, 2, 3
Show the steb by step solution
What is the mechanical advantage of an input piston with a diameter of 1.25" pushing fluid to move a piston that is 2" in diameter? Select one: a. 1.6 to 1 b. 0.39 to 1 c. 2.55 to 1 d. 0.625 to 1
The force developed in the brake cylinder is 2.74 KN and the diameter of the cylinder is 4.5 cm. If the brake cylinder is 100 mm now find the pressure developed inside the brake piston. a. 20 bar b. 19.35 bar c. 18 bar d. 17.24 bar
Briefly describe the direction of movement provided by the saddle.
show the FBD and complete solution
please answer again the image posted for formula can't be load.
Find the friction force from the given figure
P) Draw the kinematic diagram of the excavator arm and calculate the mobility of the mechanism
The right answer should be F_lift= 105 kip and F_thrust= 415 kip. I tried many times with acceleration in horizontal but couldn’t get these correct numbers.