1) Consider the "Half-wave Rectifier" circuit with a resistive loadVinParameterCut-in VoltagePeak Inverse VoltageForward CurrentSymbolVyVRRMIFD++VoutFig. 1. Half-wave RectifierWhere Vin is a sinusoidal voltage with amplitude of 6, and RL=100NSuppose the diode has the following maximum rating (according to its datasheet)wwValue500530R₁UnitmvVmAWill the diode work safely under these circumstances? Explain your answer with drawingdiode voltage and current curves.

Answered: Image /qna-images/answer/62ea28c6-a4c7-4140-a9fb-abaf56a0dd5a.jpg

1) Consider the "Half-wave Rectifier" circuit with a resistive load Vin Symbol Vy VRRM IF + + out Fig. 1. Half-wave Rectifier Where Vin is a sinusoidal voltage with amplitude of 6, and RL=10092 Suppose the diode has the following maximum rating (according to its datasheet) Parameter Cut-in Voltage Peak Inverse Voltage Forward Current R₁ Value 500 5 30 Unit mv V mA Will the diode work safely under these circumstances? Explain your answer with drawing diode voltage and current curves.

1) Consider the "Half-wave Rectifier" circuit with a resistive load Vin Symbol Vy VRRM IF + + out Fig. 1. Half-wave Rectifier Where Vin is a sinusoidal voltage with amplitude of 6, and RL=10092 Suppose the diode has the following maximum rating (according to its datasheet) Parameter Cut-in Voltage Peak Inverse Voltage Forward Current R₁ Value 500 5 30 Unit mv V mA Will the diode work safely under these circumstances? Explain your answer with drawing diode voltage and current curves.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
In the circuit shown in the figure; A) When RL = 5Kohm and capacitor C is switched on, draw VA and V0 in scale according to input voltage Vs. NOTE = diodes are ideal
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Draw vx and v0 according to the input voltages in the circuit shown in the figure. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, the threshold voltages of diodes will be VE = 0.7V.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
A silicon diode is used in the positive clipper of the figure below. Explain and sketch the output wave shape if the input is a) A sine wave with a peak value of 5V. b) A square wave with a peak value of 5V.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=3 V and V2=8 V. R www D2 DI Vin Vout V2 Maximum voltage of output waveform Minimum voltage of output waveform
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.