Fluid Mechanics: Fundamentals and Applications
Fluid Mechanics: Fundamentals and Applications
4th Edition
ISBN: 9781259696534
Author: Yunus A. Cengel Dr., John M. Cimbala
Publisher: McGraw-Hill Education
bartleby

Videos

Textbook Question
Book Icon
Chapter 6, Problem 77P

Water is flowing into and discharging from a pipe U-section as shown in Fig. P6-77. At flange (1). the total absolute pressure is 200 kPa. and 55 kgs flows into the pipe. At flange (2), the total pressure is 150 kPa. At location (3). 15 kg/s of water discharges to the atmosphere, which is at 100 kPa. Detenume the total x- and z-forces at the two flanges connecting the pipe. Discuss the significance of gravity force for this problem. Take the inomentiun-flux correction
factor to be 1.03 throughout the pipes.

Expert Solution & Answer
Check Mark
To determine

The forces along x-direction.

The net force along z-direction.

Answer to Problem 77P

The forces along x-direction is 3367.34N.

The net force along z-direction is 231.549N.

Explanation of Solution

Given information:

The total absolute pressure at flange 1 is 200kPa, mass flow rate at flange 1 is 55kg/s, the total pressure at flange 2 is 150kPa, the total pressure at flange 3 is 100kPa, mass flow rate at flange 3 is 15kg/s.

Figure-(1) represents the free body diagram of U tube.

Fluid Mechanics: Fundamentals and Applications, Chapter 6, Problem 77P

Figure-(1)
Expression for area of pipe,
A=π4d2...... (I)
Here, diameter of pipe is d.

Expression for velocity of flow,
V=m˙ρA...... (II)
Here, mass flow rate is m˙ and density of water is ρ

Expression for mass flow rate through pipe 2,
m˙2=m˙1m˙3...... (III)
Here, discharge through pipe 1 is Q1, discharge through pipe 3 is Q3.

Expression for momentum equation in horizontal direction for pipe 1,
(F Rx)1+P1A1+βm˙1V1=0...... (IV)
Here, reaction force in horizontal direction for pipe 1 is (F Rx)1, pressure at flange 1 is P1, velocity of flow in pipe 1 is V1, mass flow rate in pipe 1 is m˙1, area of pipe 1 is A1 and moment flux correction factor is β.

Expression for momentum equation along vertical direction in pipe 1,
(F Rz)1=0...... (V)

Expression for momentum equation in horizontal direction for pipe 2,
(F Rx)2+P2A2+βm˙2V2=0...... (VI)
Here, reaction force in horizontal direction for pipe 2 is (F Rx)2, pressure at flange 2 is P2, velocity of flow in pipe 2 is V2, m˙1, area of pipe 1 is A1 and mass flow rate in pipe 2 is m˙2.

Expression for momentum equation along vertical direction in pipe 2,
(F Rz)2=0...... (VII)

Expression for momentum equation along horizontal direction in pipe 3,
(F Rx)3=0...... (VIII)

Expression for momentum equation along vertical direction for pipe 3,
(F Rz)3βm˙3V3=0...... (IX)
Here, reaction force in vertical direction for pipe 3 is (F Rz)3, velocity of flow in pipe 3 is V3, mass flow rate for pipe 3 is m˙3.

Expression for net horizontal force,
FRx=(F Rx)1+(F Rx)2+(F Rx)3...... (X)

Expression for net vertical reaction force,
FRz=(F Rz)1+(F Rz)2+(F Rz)3...... (XI)

Expression for weight per unit length for pipe 1,
W1=ρA1g...... (XII)
Here, density of water is ρ and acceleration due to gravity is g.

Expression for weight per unit length for pipe 2,
W2=ρA2g...... (XII)

Expression for weight for pipe 3,
W3=0...... (XIII)

Expression for net vertical force,
FRz=FRzW1W2+W3...... (XIV)

Calculation:

Substitute A1 for A, 5cm for d1, in Equation (I).

A1=π4(5cm)2=π4(5cm× 1m 100cm)2=π4(0.05m)2=1.96×103m2

Substitute A2 for A, 10cm for d2, in Equation (I).

A2=π4(10cm)2=π4(10cm× 1m 100cm)2=π4(0.1m)2=7.85×103m2

Substitute A3 for A, 3cm for d3, in Equation (I).

A3=π4(3cm)2=π4(3cm× 1m 100cm)2=π4(0.03m)2=7.06×104m2

Refer to Table-A-3 "Properties of saturated water" to obtain density of water as 1000kg/m3

Substitute V1 for V, 55kg/s for m1, 1000kg/m3 for ρ and 1.96×103m2 for A1 in Equation (II).

V1=55kg/s( 1000 kg/ m 3 )( 1.96× 10 3 m 2 )=55kg/s1.96kg/m=28.01m/s

Substitute 55kg/s for m1, 15kg/s for m3 in Equation (II).

m˙2=55kg/s15kg/s=40kg/s

Substitute V2 for V, 40kg/s for m2, 1000kg/m3 for ρ and 7.85×103m2 for A2 in Equation (II).

V2=40kg/s( 1000 kg/ m 3 )( 7.85× 10 3 m 2 )=40kg/s7.85kg/m=5.092m/s

Substitute V3 for V, 15kg/s for m3, 1000kg/m3 for ρ and 7.06×104m2

7.06×104m2 for A2 in Equation (II).

V3=15kg/s( 1000 kg/ m 3 )( 7.06× 10 4 m 2 )=15kg/s0.706kg/m=21.22m/s

Substitute 55kg/s for m1, 1.96×103m2 for A1, 200kPa for P1, 28.01m/s for V1 and 1.03 for β in Equation (IV).

( F Rx)1+(200kPa)(1.96× 10 3m2)+(1.03)(55kg/s)(28.01m/s)=0( F Rx)1=[( 200kPa× 1000Pa 1kPa )( 1.96× 10 3 m 2 )+( 1.03)( 55 kg/s )( 28.01m/s )]( F Rx)1=[( 200000Pa× 1N/ m 2 1Pa )( 1.96× 10 3 m 2 )+1586.7665 kgm/ s 2 × 1N 1 kgm/ s 2 ]( F Rx)1=(200000N/ m 2)(1.96× 10 3m2)+1586.7665N

(F Rx)1=1979.43N

Substitute 40kg/s for m2, 7.85×103m2 for A2, 150kPa for P2, 5.03m/s for V2 and 1.03 for β in Equation (VI).

( F Rx)2+(150kPa)(7.85× 10 3m2)+(1.03)(55kg/s)(5.03m/s)=0( F Rx)2=(150kPa× 1000Pa 1kPa)(1.96× 10 3m2)+(1.03)(40kg/s)(5.03m/s)( F Rx)2=(150000Pa× 1N/ m 2 1Pa)(1.96× 10 3m2)+209.83kgm/s2×1N1kgm/ s 2( F Rx)2=(150000N/ m 2)(1.96× 10 3m2)+209.83N

(F Rx)2=1387.91N

Substitute 15kg/s for m3, 21.22m/s for V3 and 1.03 for β in Equation (IX).

( F Rz)31.03(15kg/s)(21.22m/s)=0( F Rz)3=327.849kgm/s2×1N1kgm/ s 2( F Rz)3=327.849N

Substitute 1979.43N for (F Rx)1, 1387.91N for (F Rx)2 and 0 for (F Rx)3 in Equation (X).

FRx=1979.43N1387.91N+0=3367.34N

Substitute 0 for (F Rz)1, 0 for (F Rz)2 and 327.849N for (F Rz)3 in Equation (XI).

FRz=0+0+327.849N=327.849N

Substitute 1000kg/m3 for ρ, 1.96×103m2 for A1 and 9.81m/s2 for g in Equation (XII).

W1=(1000kg/ m 3)(1.96× 10 3m2)(9.81m/ s 2)=1.96kg/m×9.81m/s2=19.26kg/s2×1N/m1kg/ s 2=19.26N/m

Substitute 1000kg/m3 for ρ, 7.85×103m2 for A2 and 9.81m/s2 for g in Equation (XIII).

W2=(1000kg/ m 3)(7.85× 10 3m2)(9.81m/ s 2)=7.85kg/m×9.81m/s2=77.04kg/s2×1N/m1kg/ s 2=77.04N/m

Substitute 327.849N for FRz, 19.26N/m for W1, 0 for W3, 77.04N/m for W2 in Equation (XIV).

FRz=327.849N19.26N/m×1m77.04N/m×1m+0N=327.849N19.26N77.04N=231.549N

Conclusion:

The forces along x-direction is 3367.34N.

The net force along z-direction is 231.549N.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Answer the following questions: a. Air lows past an object and exits as a free jet as shown in the figure. Because of the obstruction, the exit velocity is non-uniform with magnitude of 4 m/s from r = 0 to r=0.5 m and 12 m/s from r = 0.5 m/s to r = 1.0 m. It is initially calculated that the average velocity is 10 m/s, using a differential area, dA=2rrdr, what is the value of the momentum correction factor, B? 2-m-dia. a Air Wake 1-m dia. Exit -4 m/s -12 m/s b. A hydraulic turbine has 85 m of head available at a flow rate of 250 L/s. If the fluid is water and the turbine's overall efficiency is 78%, what is the mechanical power, in kW, it extracts from the water?
6-58 Water is flowing into and discharging from a pipe U- section as shown in Fig. P6-58. At flange (1), the total absolute pressure is 200 kPa, and 30 kg/s flows into the pipe. At flange (2), the total pressure is 150 kPa. At location (3), 8 kg/s of water discharges to the atmosphere, which is at 100 kPa. Determine the total x- and z-forces at the two flanges connecting the pipe. Discuss the significance of gravity force for this problem. Take the momentum-flux correction factor to be 1.03. 8 kg/s -3 cm 22 kg/s + - f10 cm 30 kg/s 5 cm
A 400cm long pipe with a smaller diameter of 3.937 inchesand a larger diameter of 11.81 inches as shown below, isinclined at a 30° angle with the horizontal. Calculate the pressure differencein KN/m²between the smaller and bigger diameter parts of the pipe if the velocity of water at the smaller diameter section is 6.56 ft/s. Pi. V₁.d₁. A1 41-0 P2. Vz, dz. Az 32 Datum

Chapter 6 Solutions

Fluid Mechanics: Fundamentals and Applications

Ch. 6 - A rocket in space (no friction or resistance to...Ch. 6 - Describe in terms of momentum and airflow how a...Ch. 6 - Does it take more, equal, or less power for a...Ch. 6 - In a given location, would a helicopter require...Ch. 6 - Describe body forces and surface forces, and...Ch. 6 - A constant-velocity horizontal water jet from a...Ch. 6 - A horizontal water jet of constant velocity V from...Ch. 6 - A horizontal water jet from a nozzle of constant...Ch. 6 - A 2.5-cm-diameter horizontal water jet with a...Ch. 6 - A 90 elbow in a horizontal pipe is used to direct...Ch. 6 - Repeat Prob. 6-20 for the case of another...Ch. 6 - A horizontal water jet impinges against a vertical...Ch. 6 - Water enters a 7-cm-diameter pipe steadily with a...Ch. 6 - A reducing elbow in a horizontal pipe is used to...Ch. 6 - Repeat Prob. 6-24 for the case of = 125°.Ch. 6 - A 100-ft3/s water jet is moving in the positive...Ch. 6 - Reconsider Prob. 6-26E. Using appropriate...Ch. 6 - Commercially available large wind turbines have...Ch. 6 - A fan with 24-in-diameter blades moves 2000 cfm...Ch. 6 - A 3-in-diameter horizontal jet of water, with...Ch. 6 - Firefighters are holding a nozzle at the end of a...Ch. 6 - A 5-cm-diameter horizontal jet of water with a...Ch. 6 - Prob. 33PCh. 6 - A 3-in-diameter horizontal water jet having a...Ch. 6 - An unloaded helicopter of mass 12,000 kg hovers at...Ch. 6 - Prob. 36PCh. 6 - Water is flowing through a 10-cm-diameter water...Ch. 6 - Water flowing in a horizontal 25-cm-diameter pipe...Ch. 6 - Prob. 39PCh. 6 - Water enters a centrifugal pump axially at...Ch. 6 - An incompressible fluid of density and viscosity ...Ch. 6 - Consider the curved duct of Prob. 6-41, except...Ch. 6 - As a follow-up to Prob. 6-41, it turns out that...Ch. 6 - Prob. 44PCh. 6 - The weight of a water tank open to the atmosphere...Ch. 6 - A sluice gate, which controls flow rate in a...Ch. 6 - A room is to be ventilated using a centrifugal...Ch. 6 - How is the angular momentum equation obtained from...Ch. 6 - Prob. 49CPCh. 6 - Prob. 50CPCh. 6 - Prob. 51CPCh. 6 - A large lawn sprinkler with two identical arms is...Ch. 6 - Prob. 53EPCh. 6 - The impeller of a centrifugal pump has inner and...Ch. 6 - Water is flowing through a 15-cm-diameter pipe...Ch. 6 - Prob. 56PCh. 6 - Repeat Prob. 6-56 for a water flow rate of 60 L/s.Ch. 6 - Prob. 58PCh. 6 - Water enters the impeller of a centrifugal pump...Ch. 6 - A lawn sprinkler with three identical antis is...Ch. 6 - Prob. 62PCh. 6 - The impeller of a centrifugal blower has a radius...Ch. 6 - An 8-cm-diameter horizontal water jet having a...Ch. 6 - Water flowing steadily at a rate of 0.16 m3/s is...Ch. 6 - Repeat Prob. 6-66 by taking into consideration the...Ch. 6 - A 16-cm diameter horizontal water jet with a speed...Ch. 6 - Water enters vertically and steadily at a rate of...Ch. 6 - Repeal Prob. 6-69 for the case of unequal anus-the...Ch. 6 - Prob. 71PCh. 6 - Prob. 72PCh. 6 - A spacecraft cruising in space at a constant...Ch. 6 - A 60-kg ice skater is standing on ice with ice...Ch. 6 - A 5-cm-diameter horizontal jet of water, with...Ch. 6 - Water is flowing into and discharging from a pipe...Ch. 6 - Indiana Jones needs So ascend a 10-m-high...Ch. 6 - Prob. 79EPCh. 6 - A walnut with a mass of 50 g requires a force of...Ch. 6 - Prob. 81PCh. 6 - Prob. 82PCh. 6 - A horizontal water jet of constant velocity V...Ch. 6 - Show that the force exerted by a liquid jet on a...Ch. 6 - Prob. 85PCh. 6 - Prob. 86PCh. 6 - Water enters a mixed flow pump axially at a rate...Ch. 6 - Prob. 88PCh. 6 - Water enters a two-armed lawn sprinkler along the...Ch. 6 - Prob. 91PCh. 6 - Prob. 92PCh. 6 - Prob. 93PCh. 6 - Prob. 94PCh. 6 - A water jet strikes a moving plate at velocity...Ch. 6 - Water flows at mass flow rate m through a 90°...Ch. 6 - Prob. 97PCh. 6 - Water shoots out of a Iar2e tank sitting a cart...Ch. 6 - Prob. 99PCh. 6 - Prob. 100PCh. 6 - Prob. 101PCh. 6 - Consider water flow through a horizontal, short...Ch. 6 - Consider water flow through a horizontal. short...Ch. 6 - Prob. 104PCh. 6 - Prob. 105PCh. 6 - Prob. 106PCh. 6 - The velocity of wind at a wind turbine is measured...Ch. 6 - The ve1ocity of wind at a wind turbine is measured...Ch. 6 - Prob. 109PCh. 6 - Prob. 110PCh. 6 - Prob. 111PCh. 6 - Consider the impeller of a centrifugal pump with a...Ch. 6 - Prob. 113PCh. 6 - Prob. 114P
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Physics 33 - Fluid Statics (1 of 10) Pressure in a Fluid; Author: Michel van Biezen;https://www.youtube.com/watch?v=mzjlAla3H1Q;License: Standard YouTube License, CC-BY