Concept explainers
A block is resting on a rough inclined surface. You observe that by increasing the angle of the incline, you can make the block start moving down the incline. Which answer best explains why the block starts moving?
a. By increasing the angle of the incline, you increase the component of the force exerted by Earth on the block, which pulls the block down the incline.
b. By increasing the angle of the incline, you decrease the maximum static friction force exerted on the block by the surface
c. by increasing the angle of the incline, you simultaneously increase the component of the force exerted by Earth on the block and decrease the maximum static friction force exerted on the block.
Want to see the full answer?
Check out a sample textbook solutionChapter 4 Solutions
College Physics
Additional Science Textbook Solutions
The Cosmic Perspective (8th Edition)
College Physics: A Strategic Approach (3rd Edition)
An Introduction to Thermal Physics
Essential University Physics (3rd Edition)
University Physics with Modern Physics (14th Edition)
- A sled and rider have a total mass of 56.8 kg. They are on a snowy hill. The coefficient of kinetic friction between the sled and the snow is 0.195. The angle of the hills slope measured upward from the horizontal is 19.5. What is the acceleration of the rider? Is the acceleration greater, less than, or equal to your result if a more massive rider uses the same sled on the same hill? Explain.arrow_forwardStarting from rest, a rectangular toy block with mass 300 g slides in 1.30 s all the way across a table 1.20 m in length that Zak has tilted at an angle of 42.0 to the horizontal. a. What is the magnitude of the acceleration of the toy block? b. What is the coefficient of kinetic friction between the block and the table? c. What are the magnitude and direction of the friction force acting on the block? d. What is the speed of the block when it is at the end of the table, having slid a distance of 1.20 m?arrow_forwardA block of ice (m = 15.0 kg) with an attached rope is at rest on a frictionless surface. You pull the block with a horizontal force of 95.0 N for 1.54 s. a. Determine the magnitude of each force acting on the block of ice while you are pulling. b. With what speed is the ice moving after you are finished pulling? Repeat Problem 71, but this time you pull on the block at an angle of 20.0.arrow_forward
- The shower curtain rod in Figure P6.7 is called a tension rod. The rod is not attached to the wall with screws, nails, or glue, but is pressed into the wall instead. Explain why the rod remains at rest, supporting the curtain. Explain why the name is misleading and come up with a better name. FIGURE P6.7arrow_forwardA worker is attempting to lift a 55.0-kg palette of bricks resting on the ground by means of a rope attached to a pulley. a. Before the worker pulls on the rope, what is the force exerted by the ground on the palette? b. The worker exerts a force of 295 N downward on his end of the rope. What is the force exerted by the ground on the palette? c. If the worker doubles the downward force, what is the force exerted by the ground on the palette?arrow_forwardA block lies motionless on a horizontal tabletop. You apply a force Fapp horizontally to the block, but it does not move. What can you say about the relative sizes and magnitudes of Fapp, the static friction force between the block and the table, and the kinetic friction force between the block and the table?arrow_forward
- If a horizontal force is applied to an object, how can you tell if an object will start moving? A.The object will start moving if any force is applied. B.The object will start moving if the applied force is greater than the maximum static friction. C.The object will start moving if the applied force is greater than the minimum static friction. D.The object will start moving if the applied force is greater than the maximum kinetic friction. E.The object will start moving if the applied force is greater than the minimum kinetic frictionarrow_forwardCalculate the magnitude of a normal force on a 22.7 kg block in the following circumstances. a. the block is resting on a level surface. b. the block is resting on a surface tilted up at 40.8 degrees with respect to the horizontal. c. the block is resting on the floor of an elevator that is accelerating upward at 2.53 m.s^2 d. the block is on the level surface and a force of 115 N is exerted on it at an angle of 40.8 degrees below the horizontal.arrow_forwardCalculate the magnitude of the normal force on a 17.7 kg block in the following circumstances. a.The block is resting on a level surface. b.The block is resting on a surface tilted up at a 20.8° angle with respect to the horizontal. c.The block is resting on the floor of an elevator that is accelerating downward at 3.78 m/s2. d.The block is on a level surface and a force of 115 N is exerted on it at an angle of 20.8° above the horizontal.arrow_forward
- 1. A car of mass 1000.0 kg is stationary on a slope forming an angle = 20° with the horizontal line. The car is located at a distance of 50 m from the foot of the slope. The coefficient of static friction between the tires and the road is μ = 0.20. a. Draw a free-body-diagram of the problem including all the information that is provided. b. Will the car slide down the slope? Motivate your answer to obtain any points. Once the car starts sliding down the slope, the coefficient of dynamic friction becomes μ = 0.15. c. Calculate the acceleration of the car. d. Calculate the velocity of the car at the foot of the slope. e. Calculate the kinetic energy of the car at the beginning and at the end of the motion. f. Calculate the total work done on the car. g. Calculate the gravitational potential energy of the car at the beginning and at the end of the motion. h. Calculate the work done on the car by the gravitational force. i. Calculate the work done on the car by the frictional force.arrow_forwardAn empty sled of mass 25 kg slides down a muiddy hill with a constant speed of 2.4 m/s The slope of the hill is inclined at an angle of 15 degrees with the horizontal. a. Calculate the frictional force on the sled as it slides down the slope b.Calculate the coefficient of friction between the sled and the muddy surface of the slope c. The sled reaches the bottom of the slope and continues of horizontal ground. Assume the same coefficient of friction. In terms of velocity and acceleration, describe the motion of the sled as it travels on horizontal ground.arrow_forwardA woman is standing on a steep hillside in the rain and is not moving. A sudden gust of wind blows down the hillside, which makes her worry that she might start sliding down the hill. However, the woman still does not slide. Which of the following statements explains why she does not slide down the hillside? A. The wind does not supply enough force to overcome the kinetic friction between the woman and the ground. B. The static friction between the woman and the ground increases as a result of the wind gust. C. The wind does not supply enough force to overcome the static friction between the woman and the ground. D. The kinetic friction between the woman and the ground increases as a result of the wind gust.arrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning