Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470501979
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 1, Problem 1.28P
An overhead 25-m-long, uninsulated industrial steampipe of 100-mm diameter is routed through a buildingwhose walls and air are at 25°C. Pressurized steammaintains a pipe surface temperature of 150°C, and thecoefficient associated with natural Convection is
(a) What is the rate of heat loss from the steam line?
(b) If the steam is generated in a gas-fired boiler operating at an efficiency of
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Small potato balls of 0.5 cm radius (can be approximated as a sphere) baked in the oven and initially at a uniform temperature of
170°C. Assume, potatoes have a density of 650 kg/m³, specific heat of 3400 J/kgk and conductivity of 1 W/mK. You want to eat
potatoes quickly without burning your tongue so that you have decided to cool them down with forced convection.
Air
h, Te
hot potato
initially
@ T;
Air temperature is 20°C and the convective heat transfer coefficient is 80 W/m?K. Calculate the time (in seconds) required for its
surface temperature to drop 130°C.
Round the value you calculated and write it as an integer!!! For example, if you find 8.2, write is as 8.
Answer:
A composite plane wall consisting of materials, 1.5-in steel (k = 312 BTU-in/HR.ft2.0F) and 2-in aluminum (k = 1400 BTU-in/HR.ft2.0F), separates a hot gas at Ti = 2000F, hi = 2 BTU/HR.ft2.0F, from cold gas at To = 80 deg F, ho = 5. If the hot fluid is on the aluminum side, find: a) Transmittance, U; b) The heat through 100 sq. ft of the surface under steady state condition and c) The interface temperature at the junction of the metals.
300°C steam flows in a stainless-steel (ss.) pipe with thermal conductivity of
50 W/m.K. The pipe has internal diameter (ID) of 40 cm, and outer diameter (OD) of 42 cm.
The pipe is placed in another ss. pipe with ID and OD 44 cm and 44.2 cm, respectively. The
gap
between the pipes is filled with steel air (use air properties at 160°C from appendix). The
convection heat transfer coefficient at the inner and the outer surfaces of the pipe is
hi = 40 W/m². K and h2= 15 W/m². K. Determine the rate of heat loss if the length of the pipe
%3D
is 10 m. Also determine the temperature at inside, intermediate and outer surfaces.
Chapter 1 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 1 - The thermal conductivity of a sheet of rigid,...Ch. 1 - The heat flux that is applied to the left face of...Ch. 1 - A concrete wall, which has a surface area of 20m2...Ch. 1 - The concrete slab of a basement is 11 in long. 8...Ch. 1 - Consider Figure 1.3. The heat flux in the...Ch. 1 - The heal flux through a wood slab 50 mm thick,...Ch. 1 - The inner and outer surface temperatures of a...Ch. 1 - A thermodynamic analysis of a proposed Brayton...Ch. 1 - A glass window of width W=1m and height H=2m is 5...Ch. 1 - A freezer compartment consists of a cubical cavity...
Ch. 1 - The heat flux that is applied to one face of a...Ch. 1 - An inexpensive food and beverage container is...Ch. 1 - What is the thickness required of a masonry wall...Ch. 1 - A wall is made from an inhomogeneous...Ch. 1 - The 5-mm-thick bottom of a 200-mm-diameter panmay...Ch. 1 - A square silicon chip (k=150W/mK) is of width...Ch. 1 - For a boiling process such as shown in Figure 1.5...Ch. 1 - You’ve experienced convection cooling if you’ve...Ch. 1 - Air at 40°C flows over a long, 25-mm-diameter...Ch. 1 - A wall has inner and outer surface temperatures of...Ch. 1 - An electric resistance heater is embedded in a...Ch. 1 - The free convection heat transfer coefficient on a...Ch. 1 - A transmission case measures W=0.30m on a sideand...Ch. 1 - A cartridge electrical heater is shaped as a...Ch. 1 - A common procedure for measuring the velocity of...Ch. 1 - A square isothermal chip is of width w=5mm on...Ch. 1 - The temperature controller for a clothes dryer...Ch. 1 - An overhead 25-m-long, uninsulated industrial...Ch. 1 - Under conditions for which the same room...Ch. 1 - A spherical interplanetary probe of 0.5-m diameter...Ch. 1 - An instrumentation package has a spherical outer...Ch. 1 - Consider the conditions of Problem 1.22. However,...Ch. 1 - If TsTsur in Equation 1.9, the radiation heat...Ch. 1 - A vacuum system, as used ¡n sputtering...Ch. 1 - An electrical resistor is connected to a battery,...Ch. 1 - Pressurized water (pin=10bar,Tin=110C) enters...Ch. 1 - Consider the tube and inlet conditions of Problem...Ch. 1 - An internally reversible refrigerator has a...Ch. 1 - A household refrigerator operates with cold-...Ch. 1 - Chips of width L=15mm on a side are mounted to...Ch. 1 - Consider the transmission case of Problem 1...Ch. 1 - One method for growing thin silicon sheets for...Ch. 1 - Heat is transferred by radiation and convection...Ch. 1 - Radioactive wastes are packed in a long,...Ch. 1 - An aluminum plate 4 mm thick is mounted in a...Ch. 1 - A blood warmer is to be used during the...Ch. 1 - Consider a carton of milk that is refrigerated at...Ch. 1 - Prob. 1.48PCh. 1 - Liquid oxygen, which has a boiling into of 90 K...Ch. 1 - The emissivity of galvanized steel sheet, a...Ch. 1 - Three electric resistance heaters of length...Ch. 1 - A hair dryer may be idealized as a circular duct...Ch. 1 - In one stage of an annealing process, 304...Ch. 1 - Convection ovens operate on the principle of...Ch. 1 - Annealing, an important step ¡n semiconductor...Ch. 1 - In the thermal processing of semiconductor...Ch. 1 - A furnace tor processing semiconductor materials...Ch. 1 - Prob. 1.58PCh. 1 - Consider the wind turbine of Example 1.3. To...Ch. 1 - Consider the conducting rod of Example 1.4...Ch. 1 - A long bus bar (cylindrical rod used for making...Ch. 1 - A 50mm45mm20mm cell phone chargerhas a surface...Ch. 1 - A spherical, stainless steel (AISI 302) canister...Ch. 1 - A freezer compartment is covered with a...Ch. 1 - A vertical slab of Wood’s metal is joined to a...Ch. 1 - A photovoltaic panel of dimension 2m4m isinstalled...Ch. 1 - Following the hot vacuum forming of a...Ch. 1 - Prob. 1.69PCh. 1 - A computer consists of an array of five printed...Ch. 1 - Prob. 1.71PCh. 1 - The roof of a car in a parking lot absorbs a solar...Ch. 1 - Consider the conditions of Problem 1.22,but the...Ch. 1 - Most of the energy we consume as food ¡s converted...Ch. 1 - Prob. 1.75PCh. 1 - The wall of an oven used to cure plastic parts is...Ch. 1 - An experiment to determine the convection...Ch. 1 - A thin electrical heating element provides a...Ch. 1 - A rectangular forced air healing duct is suspended...Ch. 1 - Consider the steam pipe of Example 1.2. The...Ch. 1 - During its manufacture, plate glass at 600°C is...Ch. 1 - The curing press of Example 1.9 involves exposure...Ch. 1 - The diameter and surface emissivity of an...Ch. 1 - Prob. 1.84PCh. 1 - A solar flux of 700W/m2K is incident on a...Ch. 1 - In considering the following problems involving...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.arrow_forward300°C steam flows in a stainless-steel (ss.) pipe with thermal conductivity of 50 W/m.K. The pipe has internal diameter (ID) of 40 cm, and outer diameter (OD) of 42 cm. The pipe is placed in another ss. pipe with ID and OD 44 cm and 44.2 cm, respectively. The gap between the pipes is filled with steel air (use air properties at 160°C from appendix). The convection heat transfer coefficient at the inner and the outer surfaces of the pipe is hi = 40 W/m?. K and h2= 15 W/m2. K. Determine the rate of heat loss if the length of the pipe %3D is 10 m. Also determine the temperature at inside, intermediate and outer surfaces.arrow_forwardA food product with 80% moisture content in a 5 cm diameter can wants to be frozen. The density of the product is 1000 kg / m³, the thermal conductivity is 1.0 W / (m K), and the initial freezing temperature is -2.25 ° C. After 10 hours in the freezing medium -35 ° C, the product temperature becomes -10 ° C. Estimate the convection heat transfer coefficient of the freezing medium. Assume the can as an infinite cylinder. h = Answer W / (m² K).arrow_forward
- A food product with 80% moisture content in a 5 cm diameter can wants to be frozen. The density of the product is 1000 kg / m cubic, the thermal conductivity is 1.0 W / (m K), and the initial freezing temperature is -1.75 ° C. After 10 hours in -25 ° C freezing medium, the product temperature becomes -10 ° C. Estimate the convection heat transfer coefficient of the freezing medium. Assume the can as an infinite cylinderarrow_forwardA steel sphere (AISI 1010), 100 mm in diameter, is coated with a dielectric material layer of thickness 1.75 mm and thermal conductivity 0.04 W/m.K. The coated sphere is initially at a uniform temperature of 500°C and is suddenly quenched in a large oil bath for which T = 100°C and h = 3000 W/m².K. Estimate the time, in h, required for the coated sphere temperature to reach 150°C. Hint: Neglect the effect of energy storage in the dielectric material, since its thermal capacitance (pc)is small compared to that of the steel sphere. t = harrow_forwardA silicon chip is encapsulated so that, under steady-state conditions, all the power dissipated by it is transferred by convection for a fluid current with h=1000 W/(m2.K) and Tꚙ=25oC. An aluminum plate (k=237 W/(mK)), 2 mm thick, is placed on the chip surface, the contact resistance on the chip/aluminum interface is 0.5x10-4 (m2.K)/W. If the chip area is 100 mm2 and the maximum allowable temperature is 85 oC, what is the maximum allowable power dissipation on the chip?arrow_forward
- Small potato balls of 0.5 cm radius (can be approximated as a sphere) baked in the oven and initially at a uniform temperature of 160°C. Assume, potatoes have a density of 650 kg/m³, specific heat of 3400 J/kgK and conductivity of 1 W/mK. You want to eat potatoes quickly without burning your tongue so that you have decided to cool them down with forced convection. Air h, T. hot potato initially Air temperature is 20'C and the convective heat transfer coefficient is 140 W/m²K. Calculate the time (in seconds) required for its surface temperature to drop 90°C. Round the value you calculated and write it as an integer!! For example, if you find 8.2, write is as 8. Answer:arrow_forwardQ1:(a) Define convection and its types. Either free or forced convection is good by considering an example. (b)Explain, motorcycle engine is either considered as free or forced convection. Justify your answer.arrow_forwardNeed answer ASAP! Thank you Water at 5°C is being used to cool apples from an initial temperature of 25° to 10°C. Thewater flow over the surface of the apple creates a convective heat-transfer coefficientof 10 W/(m2-K). Assume the apple can be described as a sphere with an 8 cm diameterand the geometric center is to be reduced to 10°C. The apple properties include thermalconductivity of 0.4 W/(m-K), specific heat of 3.950 kJ/(kg-K), and density of 940 kg/m3 a. Determine the time that the apples must be exposed to the water.b. If the apple is submerged only for 2 hours, what will be its center temperature?arrow_forward
- A thermocouple is initially at temperature of T; and it is used to measure the temperature of air (Tair). It would take a while for the temperature of the thermocouple junction to approach Tair. The thermocouple junction can be approximated by a copper sphere of 0.5 mm in diameter. Using the lumped system analysis (chapter 5, undergraduate heat transfer textbook), derive an expression for T(t) (it should look like: (T(t)-Tair )/(Ti-Tair) = e, where T; is the initial temperature of the thermocouple, and Tair is the air temperature). Calculate the time constant 7 (assuming the convection heat transfer coefficient h=5 W/m²K). Use the thermal properties of copper from your undergraduate textbook or any other books. Usually t=3t is used as the response time of the thermocouple with 5% measuring error. Explain why? If the thermocouple size is increased to 5 mm in diameter, what is the response time?arrow_forwardSmall potato balls of 0.5 cm radius (can be approximated as a sphere) baked in the oven and initially at a uniform temperature of 160°C. Assume, potatoes have a density of 650 kg/m, specific heat of 3400 J/kgK and conductivity of 1 W/mK. You want to eat potatoes quickly without burning your tongue so that you have decided to cool them down with forced convection. Air h, T. hot potato initially Air temperature is 20°C and the convective heat transfer coefficient is 140 W/m?K. Calculate the time (in seconds) required for its surface temperature to drop 90°C.arrow_forwardH.W. Q1: Consider a hot automotive engine, which can be approximated as 0.40m wide, and 0.8m long rectangular block. The bottom surface of the block is at a temperature of 80°C and has an emissivity of 0.95. The ambient air is at 20°C, and the road surface is at 25°C. Determine the rate of heat transfer from the bottom surface of the engine block by convection and radiation as the car travels at a velocity of 80 km/h. Assume, the flow to be turbulent over the entire surface because of the constant agitation of the engine block. k = 0.02735 W/m.°C v=1.798×10* m²/s Air properties at Tf= 50 °C: Pr = 0.7228 Answer: Qcony = 1363 W, Qrad = 132 W, Qotal = 1495 w Hint: Use the correlations (equations) of average Reynold number (ReL). L = 0.8 m Engine block Air V, = 80 km/h T. = 20°C T; = 80°C ɛ = 0.95arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license