The post below is supported by a pin at A and a weightless link BC post below, using the method of sections: 3m B D -6KN 3m Im 3m The absolute magnitude of the internal momentin kN-m at point D is mostly near

The post below is supported by a pin at A and a weightless link BC post below, using the method of sections: 3m B D -6KN 3m Im 3m The absolute magnitude of the internal momentin kN-m at point D is mostly near

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: wing most nearly gives the saving’s in lining per meter length of channel that could have been…

A: As per QnA guidelines, only first question will be covered

Q: 1. Draw the shear and moment diagrams for the overhang beam. C

A: Overhang beam is given. We need to draw shear and moment diagram for the beam.

Q: termine the value of bending moment in column 2 (in kip-ft, absol bay width is 21 ft the story…

Q: 2. Using the flow net drawn, calculate the hydraulic uplift force at the base of the hydraulic…

A: From the given diagram, The height at the upstream side (H) and at the downstream side (h) is, width…

Q: Q1:- discus the following sentence: - Most crops show significant signs of stress, such as wilting…

A: Wilting in crops is often a visible sign of stress, typically due to inadequate water availability,…

Q: h The bridge deck represented by a beam element shown is designed to support 20 kN/m of uniformly…

A: Given Load 25 and 40 kNUDL 20kN/mSpan 16 mTo find out Maximum reactionMaximum shearMaximum moment

Q: A vertical Sluice gate 2m wide and 2 m deep contains water on its either side. The water on its…

A: A vertical Sluice gate width = 2m depth = 2mUpstream side water…

Q: Briefly explain what 'half-life' is. Then, use the following expression of batch system (zero-order…

A: Half Life : Half-life is the amount of time taken for the decay of a substance to decay from intial…

Q: steel tube. Total axial deformation is 1 hat is the compressive load, P? Assume: uter dia. =1" nner…

A: Given data :Length of member (L)=20inAxial deformation = 0.5inModulus of elasticity of the steel is…

Q: n

Q: Given the simply supported beam below, and using the method of sections: SIE 1.5m The internal shear…

A: Given:Required:Shear force at point C

Q: What is the most probable cause of this casing failure? 0253 The pipe was under tension, decreasing…

A: What is the most probable cause of this casing failure?The pipe was under tension, decreasing the…

Q: 1. It is estimated that the BOD of raw sewage received at a treatment plant serving a population of…

A: Population = 20,000BOD loading = 0.17 lbm/dayinfluent BOD= 30%

Q: 1. It is estimated that the BOD of raw sewage received at a treatment plant serving a population of…

Q: Find the deflection using PARTIAL DERIVATIVE method 8 KN -3 m D -3m B 4 kN C

Q: An abrupt rise of 1m was designed to control a hydraulic jump generated after a 5 m wide sluice gate…

A: Abrupt rise = 1 mWidth of sluice gate = 5 mOpening = 0.25 mFlow discharge = Flow depth = 1.25 mTo…

Q: A one-way both ends continuous slab is to support the moments tabulated. Consider L= 5m. Fc’ = 21MPa…

A: L= 5mFc’ = 21MPafy = 415MPa.Dead load Moments: +42KN.m at midspan ;-67KN.m at support;Live Load…

Q: 9. 8.5m compacted fill is to be placed over the soil profile. Cosnolidation tests are done on…

A: Hfill = 8.5m = 20.3 kN/m3

Q: Determine the magnitudes of the forces in each pin of the loaded frame. Answers: A= i 855 B= i C=…

Q: Q1. Check for the compactness and determine the values of My and Mp for the W14x120 section used as…

A: W14x120 sectionsteel grade 50*NOTE: As per Bartleby's guidelines we are supposed to answer only…

Q: What does the moment diagram look like 分 1 24 P →>> H An L

Q: A 500-ft curve, 9₁ = -2.00%, 92 = +3.00 %, VPI station = 98 + 10, VPI elevation = 5388.26 ft,…

Q: ater with a total head of H= 12 m flows freely from a reservoir into a concrete trapezoid annel with…

A: Water with a total head of different longitudinal slopes of,The channel was designed using the most…

Q: Calculate the stress developed in the following members that are each subjected to an axial tensile…

A: Calculate the stress developed in the following members that are each subjected to an axial tensile…

Q: Problem 1: Determine the slope and deflection of the beam at points B and C using double.…

A: As per company policy we can only answer first question.Kindly post other questions as seperate…

Q: A 500-ft curve, grades of g₁ = +2.50% and 9₂ = -3.00%, VPI at station 96 + 80 and elevation 835.26…

Q: Consider the given figure. Given: P = 110 kN.m. 30 kN.m A 20 kN/m 6 m raw the shear and…

Q: structural engineer wants to consider placing the base of the building so deep that the soil below…

A: Weight of buliding = 10790 kipsSize of buliding = 65×65 ftCohesion = 418 psfWeight of soil = 118 psf…

Q: [15]. Convection is commonly classified into three sub-modes: Forced convection, Natural (or free)…

Q: A two-story home with infiltration rate of 0.5 ach has 100 m2 of floor space per floor and a total…

Q: A 500-ft curve, g₁ = -2.00%, 92 = +3.00%, VPI station = 98 + 10, VPI elevation = 5388.26 ft,…

Q: escribe two advantages of using a waste-to energy facility to deal with waste compared to trad

A: A waste-to-energy (WTE) facility is a specialized facility that processes waste to generate energy…

Q: A rigid, uniform, weightless, horizontal bar is connected to three vertical members P, Q and R as…

A: Given data - K = 10 KN/mFind out - Vertical load W ?

Q: It is estimated that the BOD of raw sewage received at a treatment plant serving a population 20,000…

Q: Determine the force in each member of the truss, and state if the members are in tension or…

Q: 9) A well is located in a confined aquifer near the intersection of a constant head and impervious…

Q: etermine the required slope if the channel is trapezoidal with depth equal to the width of the…

A: DATA GIVENQ = 2.1 m3/sec" data-mce-style="display: inline-block; line-height: 0; text-indent: 0px;…

Q: calculate the irrigation interval if

Q: 2. The average wastewater flow from a community of 20,000 is 125 gpcd. The 5 day, 20 deg C BOD is…

A: Population = 20000To Find:1) Settling tank surface area2) Settling tank diameter3) BOD removal in…

Q: Locate the X–X and Y–Y centroidal axes for the area shown.

Q: HW Draw I.L for RAI REI REI VB, VELI VER, VD. MA. Mc. Mo गर B + 4 C D q5 4|2|2|3| 5

A: A continuous beam with internal hinge is shown in the above figure. Static Indeterminacy of the…

Q: The internal normal force in kN at point C is mostly near

Q: For the following indeterminate frame (with SI = 1) determine the reactions then draw the shear and…

Q: hydraulics *use handwritten A rectangular channel 5.50 m wide and 1.30 m deep is laid on a…

Q: 2. A line load of q per unit length is applied at the ground surface as shown in the Figure below…

Q: . What is the length is storm pipe that is constructed between a point 50.00 ft left of sta. 3+50 nd…

A: Station 5+00 = 500 ftStation 3+50 = 350 ftradius of the centerline = 600 ft

Q: The following data on the substrate removal rate and the substrate concentration is available for…

A: We are using Michaelis-Menten equation

Q: A large oil storage tank 90 meters in diameter is to be constructed on the soil profile shown in the…

Q: A 500-ft curve, 9₁ = -2.00%, g2 = +3.00%, VPI station = 98+10, VPI elevation = 5388.26 ft, stakeout…

A: g1 = -2.00%g2= +3.00%L = 500ftPvi elevation = 5388.2

Q: The first thing you need to do in a tape and offset survey is: A Identify some fixed reference…

A: The first thing you need to do in a tape and offset survey is:A Identify some fixed reference…

Question

how do i solve the attached civil engineering/internal forces problem?

The post below is supported by a pin at A and a weightless link BC post below, using the method of sections:
3m
E
→6KN
B
3m
Im
3m
The absolute magnitude of the internal moment in kN-m at point D is mostly near_

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: State the given data

VIEW

Step 2: Free body diagram

VIEW

Step 3: Moment at D

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

4KN 2KN E F 6KN 8KN 3m ID - 3span @ 4m=12meters Analyze the given Compound Truss: Solve for the member forces at EF, BF and CE
A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is supported by bolts at A and B that are in the single shear. The bar is loaded by 4kn at point D. Dtermine the resultant action at B
Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa. c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4. Use appropriate (SI) units as it applies (if any.)
C 120 N-m A 300 60° 200 B 400 E 60° 300 200 Dimensions in millimeters y 600 N G Determine the magnitude of the force (in N) of the x-component of the internal pin at B.
The 23in vertical rod CD is welded to the midpoint C of the 50in rod AB. Determine the moment AB of the 235lb force P
36 kip 15 It A A is Roller B is Pin c is Pin 15 fb 15ft G 15ft 24 kip 15 ft Q/Determine the Force in all bars the truss. E 20 ft
Determine the force in members DE and DF of the truss shown when P= 25 kips. F D H 7.5 ft В A L C E G I K P P P 6 panels @ 6 ft = 36 ft |kips. [(Click to select) | kips. (Click to select) The force in DE is The force in DF is
4 kN 4 kN 3 kN 2 kN B C D 3 m H 2'm - 5 m- -5 m- -5 m- - 5 m- Q4- The figure shows a truss that is supported at A by a pin and a roller at E. The truss is subjected to vertical forces. Determine the following: (a) check for zero-force members and identify such members (b) The Force Reactions at the supports are: Ax kN Ay kN Ey k N (c) The internal Force in member CD, FcD i . kN, specify (T) or (C) (d) The internal Force in member CF, FCF İS. . kN, specify (T) or (C) (e) The internal Force in member CD, FcG is . kN, specify (T) or (C)
The truss supported by a pin at D and a roller at A, is subjected to the vertical load as shown. Using any analysis method, please determine the force in the four truss members around joint E (AE, BE, CE, and DE). Note whether the members are in tension or compression. A -2 m- E B 400 N 2 m D
2-2 A 100-N force is applied at end C of the rod as shown. c) Assess the effect of the angle being varied from 0° to 360° to the moment of the 100-N force about point A. [b) (i) MA=0 N-m; (ii) MA=-24k N-m; (iii) MA=-12k N.m] 2-3 A 600-N force is applied on end D of the bent rod as shown. c) Assess the effect of the angle being varied from 0° to 180° to the moment of the 600-N force about point A. [b) (i) MA= 180 N-m; (ii) MA= - 480k N-m; (iii) MA= 180k N-m; (iv) MA=- 432k N.m] Figure IA Figure 150 mm P2-2 600 N 50 cm B P2-3 90 mm 0 000 B 30 cm C 100 N 30 cm
1. Use the method of sections to determine the internal forces in members BC, GC, and GF. The structure is supported by a pin at D and a roller at E. A -2 m- 1000 N B G a a -2 m- C F -2 m- E 2 m
G5 // The bar AB is considered to be absolutely rigid and is horizontal before the load of 10000N is applied. The connection at C is a pin, and AB is supported by the bronze rod EA and the steel rod FB. The length of EA is 1.5m and FB is 2.5m. Neglect any possibility of lateral buckling and the weights of all bars „Calculate the stresses in each rod. For bronze E=100 GPa, A=60 mm? for steel E=200 GPa, A= 25 mm? F Steel L=2.5m B. 3m 2m- Bronze L=1.5m 10000N