2. Using the flow net drawn, calculate the hydraulic uplift force at the base of the hydraulic structure per meter length (measured along the axis of the structure) 3.34m 10m Se SE 1.67 m Impermeable layer 18.32m- 10 m Scale E H 5E

2. Using the flow net drawn, calculate the hydraulic uplift force at the base of the hydraulic structure per meter length (measured along the axis of the structure) 3.34m 10m Se SE 1.67 m Impermeable layer 18.32m- 10 m Scale E H 5E

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.14P

See similar textbooks

Related questions

Q: A channel is used as a tension member with the web of the channel welded to a 9.5 mm thick gusset…

A: To solve these problems, we'll use the Load and Resistance Factor Design (LRFD) approach. LRFD…

Q: P12.3. Draw the influence lines for the reactions at supports A and C, the shear and moment at…

Q: 6 6-22. The beam is subjected to a uniform live load of 1.2 kN/m, a dead load of 0.5 kN/m, and a…

A: Given Span 16 mDead load = 0.5 kN/mLive load = 1.2 kN/m and 40 kNTo find out Maximum positive shear…

Q: What is the equation for bending moment between C and B, the midpoint and righ side of the beam (6…

A: Determine the moment equation for the span CB (6ft<x<12ft).

Q: Water flow in a river channel has velocity V = 5m/s, depth d = 2.5m, slope = 0.0008 and friction…

A: Flow depth, Slope, Characteristics of bed material, Friction factor, water density,

Q: A simple four legs intersection needs a fixed time signal and the traffic flow condition is shown as…

A: For a simple four legs intersectionthe lost time per phase is 4.2 secondsTo determine (a) the…

Q: Ex4-5: Calculate the amount of needed water to irrigate farm of 160 donum area through the duration…

Q: Hardening of concrete is caused by "Hydration" True False

A: Given:Hardening of concrete is caused by "Hydration"TrueFalse

Q: draw a plumbing base in a picture

A: Plumbing : It is defined as the system of pipes, fixtures, and other sanitary equipment which are…

Q: A flood occurs in the main channel having a trapezoidal section with a base width of 4.5 m. If the…

A: Mean velocity V = 1.2 m/sBase width, B= 4.5 m

Q: A one-way both ends continuous slab is to support the moments tabulated. Consider L=5m, Fc’=21MPa…

Q: 1.-) Draw the shear force and bending moment diagrams for the beam. A 5 pies- 6 kip -6 pies- 12 kip…

Q: PROBLEM NO. 2: Two plates each with thickness t = 16mm are bolted together with 6-22mm diameter…

A: Data Given:S1 = 40 mmS2 = 80 mmS3 = 100 mmt = 16 mmBolt diameter (db)= 16 mmAsked:Allowable strength…

Q: For the beam loaded as shown, determine the bending moment at B. Indicate if negative. 100 kN - m CH…

Q: (Froude number) The average velocity and average depth of a river from its beginning in the…

A: Given data : For 50 mi distance average velocity (V) = 4 ft/sAverage depth (D) = 5.4 ft Froude…

Q: Draw the shear force and bending moment diagram and label the values of the largest positive and…

Q: Good

Q: CHAP. 7] کیجا f. TRUSSES AND CABLES Solve for the forces in kips in the members CE and DF in the…

A: Forces in kips in the members CE and DF in the truss =?Use the method of sections

Q: Problem 2. A base line is measured and subsequent calculations show that its total length is…

A: Total length = 4638 ftstandardization temperature = 500Fstandardization tension = 30 lbfmeasured…

Q: The discharge of water through a rectangular channel of width 10 m is 30 m³/s when depth of flow of…

A: Rectangular channel Width of the channel (B) = 10m Discharge (Q) = 30 m3/s Depth of the flow (y) =…

Q: Calculate the omitted lengths of the lines of BC and CD of a closed traverse ABCDEA, using the…

Q: In a Grid coordinate system you need to divide the survey zone into: Question 20Select one: A.…

A: Correct Answer: Option B is the correct answer.Since we know that in a grid coordinate system, all…

Q: Analyze the frame in the given figure. Given: El is constant, X=65 kN. 6 kN/m 50 kN 4 m3 m- D X KN…

Q: Find the magnitude of the internal shear force at point D for the given figure with a distributed…

A: Determine the internal shear force at point D.

Q: 20' B hinge C 8 R₁, Re M. and V 10' D 10' E Draw an influence line for reaction at A and determine…

Q: Water is pumped from the river through a 45-mm-diameter hose having a length of 3 m. The friction…

A: Diameter of the pump hose = 45mm = 0.045mLength = 3mFriction…

Q: 1. Describe the condition of plain stress and plain strain conditions in terms of stress and strains…

A: Plane stress and plane strain are two types of simplifications for the analysis of solid mechanics…

Q: For the following indeterminate beam (with SI = 1) determine the reactions then draw the shear and…

Q: B f 900 lb 2 ft 200 lb/ft 6 ft The properties of the timber cantilever beam ABC are I = 60 in.4 and…

Q: Calculate the components of the resultant force at support A, measured in Newtons (N). Determine the…

Q: 1. It is estimated that the BOD of raw sewage received at a treatment plant serving a population of…

A: Population = 20,000BOD loading = 0.17 lbm/dayinfluent BOD= 30%

Q: Water at 25°C is pumped into the galvanized iron pipe branch consisting of two 50-mm-diameter pipes…

Q: what would be the moment diagram of the fram

Q: A flow rate of 2.1 m^3/s is to be carried in an open channel at a velocity of 1.3 m/s. N=0.020.…

A: *Note: As per Bartleby's guidelines we are supposed to answer only first question. Kindly repost…

Q: Find the internal shear force at point B, which is 1m from the fixed support located at point A.…

Q: A Click Submit to complete this assessment. Question 5 At what Horizontal Distance (HD) in feet from…

A: Rod reading is given we need to find out the Horizontal Distance

Q: For the truss shown, Find the height of the truss? Analyze the load on each member of the truss?

Q: 2. The average wastewater flow from a community of 20,000 is 125 gpcd. The 5 day, 20 deg C BOD is…

A: Population = 20000To Find:1) Settling tank surface area2) Settling tank diameter3) BOD removal in…

Q: Consider the given figure. Given: P = 12 kN. P A C-0000 ←0.4 m→ 2 kN/m 13.6 KN -0.8 m- Determine the…

Q: On the given beam, find the following unknowns using the slope-deflection method. Assume that E is…

A: Given:Required:Fixed end moment for member BAMoment at support DInternal moment of member BCNote: As…

Q: A construction company is bidding on a project comprising five high-rise buildings to be erected one…

A: The average material cost per square foot for each use can be calculated by considering the purchase…

Q: The column section shown below has ties, concrete compressive strength fe' = 5000 psi, and flexural…

Q: For the beam shown, determine the reaction at the roller support when wo = 18 kN/m. (Round the final…

A: Since, the given beam is indeterminate, so apply the compatibility condition i.e. total deflection…

Q: 9) A well is located in a confined aquifer near the intersection of a constant head and impervious…

Q: etermine the force in brace 2 if the braces are ass cory height is 8 ft, the bay width is 29 ft, and…

Q: On the given beam, find the following unknowns use the SLOPE DEFLECTION METHOD. Assume that E is…

Q: Find the location of the centroid and moment of inertia with respect to centriodal axes

A: The location of the centroid =?Moment of inertia with respect to centroidal axes =?

Q: ater with a total head of H= 12 m flows freely from a reservoir into a concrete trapezoid annel with…

A: Water with a total head of different longitudinal slopes of,The channel was designed using the most…

Q: Give three examples of different types of tensile structures and their application

A: A tensile structure is a type of construction characterized by elements such as cables, membranes,…

Q: 6.10 Refer to Figure P6.5a. The uniform surcharge is time dependent. Given q (kN/m²) = 2t (days)…

A: Given surcharge,

Concept explainers

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.

Question

2. Using the flow net drawn, calculate the hydraulic uplift force at the base of the hydraulic structure
per meter length (measured along the axis of the structure)
3.34m
10m
Sa
1
SE
m
1.67 m
Impermeable layer
18.32m
10 m
Scale
GE
H

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data:

Step 2: Calculation:

Step 3: Calculation:

Solution

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

4. A steel beam, with square cross-section of side 10 mm and a simply supported length of 8.0 m from points A to B, has a rigid vertical rod attached at its midspan. This rod connects the beam to a hydraulic jack system as shown in Figure 3. Attached at the lower end of the rigid vertical rod is a rigid plate of diameter 30 cm. This plate serves as a stopper on one end of the hydraulic system containing a liquid with a specific gravity of 0.45. At the opposite end of the hydraulic system, which is 0.10 m higher, another rigid plate, having a diameter of 2.0 m, rests on top of the liquid. At its center, a 50 N concentrated force is applied. Considering the weight of the beam as uniformly distributed all throughout (use density of steel as Pateet = 7850 kg/m³), while neglecting the weights of the rigid plates and the rigid rod, (a) determine the reactions at supports A and B. (b) Draw the shear and bending moment diagram of the beam. Obviously, you don't need to enclose the diagrams in a…
1. In a system with 4 reservoirs and 1 pipe junctions, how many hydraulic headloss equations are formulate? A. 3B. 2C. 1D. 4E. 5 2. In turbulent flow, which is correct?BJ: higher Re value has lower friction factorJB: lower Re value has lower friction factorGroup of answer choices A. BJ is true and JB is false B. BJ is true and JB is true C. BJ is false and JB is false D. BJ is false and JB is true 3.which of the following is always the same for horizontal closed conduit? A. Total headB. Velocity headC. Elevation headD. Pressure head
Example 8.2 Refer to the e log o' curve shown in Figure 8.12. a. Determine the preconsolidation pressure, o. b Find the compression index, Ce 1.0 0.9- 0.8 0.7 0.6 03 10 Effective pressure, o (ton/t) (log scale) Figure 8.12
3. The basic elements of a hydraulic press are shown in Fig. 1. The plunger has an area of 1cm², and a force F₁ can be applied to the plunger through a lever mechanism having a mechanical advantage of 8 to 1. If the large piston has an area of 150 cm², what load F2, can be raised by a force of 30 N applied to the lever? Neglect the hydrostatic pressure variation. Hydraulic fluid Plunger
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine The pressure at section B, ps (kPa) FMx (N) FMY (N) de = 100 mm da = 150 mm 30°
Example 9.5 • Determine the hydraulic radius of the section shown in Fig. 9.9 if the inside dimension of each side of the square is 250 mm and the outside diameter of the tube is 150 mm. D 150-mm diameter 250 mm
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine a) FMY (N) b) Fpx (N) c) Fpx (N) de = 100 mm da = 150 mm 30° A
Through the pipeline system in the figure calculate gauge and absulate presures at A and B
CORRECT LETTER PLS 1. In a system with 4 reservoirs and 1 pipe junctions, how many hydraulic headloss equations are formulate? A. 3B. 2C. 1D. 4E. 5 2. In turbulent flow, which is correct?BJ: higher Re value has lower friction factorJB: lower Re value has lower friction factorGroup of answer choices A. BJ is true and JB is false B. BJ is true and JB is true C. BJ is false and JB is false D. BJ is false and JB is true 3.which of the following is always the same for horizontal closed conduit? A. Total headB. Velocity headC. Elevation headD. Pressure head
Orifice meter with orifis cross-section 0.00785 m2 is inserted in a pipe of cross-section 0.0314 m2. The pressure gauge fitted upstream and downstream of orifice give reading of 19.62 N/cm2 and 9.81 N/cm2 respectively. Determine the value of dischareg using Cd=0.6.
4.1 A line load of q = 60kN/m with a = 0 is placed on a ground surface as shown in Figure P4.1. Calculate the increase of pore water pressure at M immediately after application of the load for the cases given below. (a) z = 10m, x = 0m, v=0.5, A=0.45. (b) == 10m, x= 2m, v= 0.45, A=0.6. 2 m 4. G.W.T. Clay XI 1
Problem 4: An inclined permeameter tube is filled with layers of soil of different permeability as shown below. Find the total head, elevation head and pore water pressure at points (A-B-C-D) with respect to the given datum, Given: 1.5k1=2k2=3k3=k4 k4=2x10-3 cm/sec 35 сm 9 cm K4 K3 K1 K2 15 cm 11 cm 7 cm 4 cm Datum شاشة 4cm