Q1: Draw a flowchart for work the traffic lights ? Q2: Write the algorithm required to find the largest number from the numbers A, B. and C ? Q3: Write the algorithm for a program that calculates the cost of the phone bill according to the following three rules ? (1) The first 50 minute: each minute with 10 DI. (2) The next 100 minute: each minute with 15 DI. (3) Whats more: each minute with 20 DI. 04: Write the algorithm to find the sum of the number from 1 to 20 ? 05: Draw a flowchart for the following algorithm ? (1) Put value of sum equal zero and value of N equal 1. (2) Add N to the sum (3) If N<6 add 1 to the current value of N, then go to step 2. (4) Print value of sum. (5) Stop 06: Draw a flowchart to find the sum m of real numbers (X, X2, X X) So that the result is the sum of the numbers T such that T = E, X, ? 07: Write an algorithm to print the multiplication table for number 92 08: Write an algorithm to calculate the average numbers that the factorial result of last number equal to 5040? 0o Draw a lowchart to find the greater common factor between two numbers? 010: Draw a flowchart to find the prime numbers for N numbers?

Q1: Draw a flowchart for work the traffic lights ? Q2: Write the algorithm required to find the largest number from the numbers A, B. and C ? Q3: Write the algorithm for a program that calculates the cost of the phone bill according to the following three rules ? (1) The first 50 minute: each minute with 10 DI. (2) The next 100 minute: each minute with 15 DI. (3) Whats more: each minute with 20 DI. 04: Write the algorithm to find the sum of the number from 1 to 20 ? 05: Draw a flowchart for the following algorithm ? (1) Put value of sum equal zero and value of N equal 1. (2) Add N to the sum (3) If N<6 add 1 to the current value of N, then go to step 2. (4) Print value of sum. (5) Stop 06: Draw a flowchart to find the sum m of real numbers (X, X2, X X) So that the result is the sum of the numbers T such that T = E, X, ? 07: Write an algorithm to print the multiplication table for number 92 08: Write an algorithm to calculate the average numbers that the factorial result of last number equal to 5040? 0o Draw a lowchart to find the greater common factor between two numbers? 010: Draw a flowchart to find the prime numbers for N numbers?

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter29: Service-entrance Calculations

Section: Chapter Questions

Problem 3R: a. What is the ampere rating of the circuits that are provided for the small-appliance loads? _____...

See similar textbooks

Similar questions

A person is recording measurements from an analog data reader. During the first reading, he was not looking at the meter from a straight angle. He gets the reading of 72. At a second reading later he looks straight at the machine and gets the reading of 70. a) Which reading number is nearer to the actual value? What is the error type that happened in that reading? b) c) Suppose the data reader becomes faulty due to the extreme heat and gives a third measurement of 65. What type of error happened now? The data reader is working properly now, but there is a slight difference between two readings for the same measure. What type of error happened now and how can we d) minimize it?
Create a sequence detector that detects the sequence 1001 or 0110 by using Verilog Code. Construct the modules for both the Moore and Mealy models. Demonstrate your simulation results using the following input sequence for the test fixture (test bench): x= 0010011010010110010110110100
step-by-step with calculation needed
Q.1) What is the type of PCI transaction diagram? Redraw the timing when the IRDY# and TRDY# is ready from cycle 2 to end of transaction and explained the function of each signals appear in diagram. CLK FRAMEN AD Address Data-1 Data-2> Data-3 C/BE# Bus Cmd BE# IRDY# TRDYW DEVSEL# Data Phase Data Data Address Phase Phase Phase
I opened a broken Coin Pusher Arcade game to fix, and I saw a burned IC. Between Microprocessor and Microcontroller, what kind of IC do you think is that? And why?
Hello. I think I am close but I wanted to check my process. What is the best way to take on this problem. Thank you.
VI. FILL-IN QUESTIONS: 1. Before the TRIAC is triggered on, the voltage across its main terminals is equal to the voltage. 2. When the TRIAC is triggered on, the voltage across its main terminal is about V. 3. Once the TRIAC is conducting, the gate_control the current to flow through the TRIAC. 4. The TRIAC can be turned off by reducing the current through it below its The TRIAC can have_or__terminal voltage and be triggered on by_applied on the gate.
How can random error be reduced? a.Using a more accurate instrument. b.Change the measuring instrument. c.Recalibrate the measuring instrument. d.Take several measurements and determine the average. Plz do fast ASAP
1 _ Compare between the status and control flags? Explain the status flags for the operation AEH+37H ? 2) 2 _What are the purposes of both segmentation and physical generation? Explain with draw and numerical example?
Q.1) Assume that the control of a bottle filling system is performed with an 8051 microcontroller. • The start and stop of the conveyor is controlled by the P1.0 pin. • The bottles are moving on the conveyor and detected with a sensor. When they arrive at the filling place, they are detected with a logical "1" signal, otherwise they are detected with a "0" signal. • A valve connected to P1.1 turns on for 10 seconds to fill each bottle. • At every X bottles, the conveyor will stop for 8 minutes and then start again. The remaining time to restart in the waiting period is displayed in minutes on the 7-segment display. • Logic "1" is detected from P1.3 during the operation of the system. Logic '0' is detected from P1.3 at the end of the shift. • At the end of the shift, the number of the filled bottles will be determined and saved in a memory location as 2 bytes. Write the required program. (Crystal Frequency:12MHZ). NOTE: X number will be taken as the last 2 digits of 59
Q1.A. A sequence detector has an input w and an output z. The machine is a sequence detector that produces z = 1 when the previous two values of w were 00 or 11; otherwise z = 0. a) Design Moore FSM (Find the state diagram and the state table) use the letters S0,S1,S2,...to name the states. b) Reduce the number of states by using the partitioning minimization procedure.
PLS PLS SHOW COMPLETE SOLUTION AND WRITE LEGIBLY. DRAW CIRCUIT DIAGRAM. PLS PLSS SHOW HOW THE EQUATIONS REDUCED TO NEEDED.