3 Consider the combinational circuit shown below. The propagation delay for each unit is indicated in ns. Assume all other delays are zero. 8 ns C(x,y) 10 ns 10 ns y - 7 ns 5 ns 5 ns a) What is the latency and throughput of the circuit as shown? b) Indicate where storage registers should be placed to create a two-stage pipeline with maximum throughput. c) What is the latency and throughput of the two-stage pipeline in part b?

3 Consider the combinational circuit shown below. The propagation delay for each unit is indicated in ns. Assume all other delays are zero. 8 ns C(x,y) 10 ns 10 ns y - 7 ns 5 ns 5 ns a) What is the latency and throughput of the circuit as shown? b) Indicate where storage registers should be placed to create a two-stage pipeline with maximum throughput. c) What is the latency and throughput of the two-stage pipeline in part b?

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 25RQ

See similar textbooks

Similar questions

4. A data signal with bipolar voltage levels is shown below. The decision threshold is 0 volts. The logic levels are +1 volt for logic 1 and -1 volt for logic 0. Noise with the P.D.F. shown corrupts the signal. Find the probability of error at some instant of time on the condition that logic 0 is sent. LOGIC 1 +1 VOLT -2 1/2 دمت ~IN kla THRESHOLD +2 NOISE P.D.F. -I VOLT. LOGIC 0
What is not a possible solutions to improve performance ..... of PCM?a. Use of linear PCM codesb. Use of non-linear PCM codes tryc. Use of companded systemsd. Increase number of PCM bits
Most Digital transmission are "self-clocking " in that they derive the bit synchronization from the signal itself. To do this, the system use the transitions between positive and negative voltage levels. These transition help define the boundaries of the bit intervals. a) Plot the NRZ-L signal for the data stream 4 bits of 1s followed by 4 bits of Os. Explain why this code has a synchronization problem? b) Repeat part ) for Manchester encoding scheme and explain how the synchronization problem has been addressed.
a) Multiply the binary numbers 01001111 (multiplicand) and 00000101 (multiplier) by using the directaddition method. b) in image c)in image
A new floating point representation is proposed so that implicit normalization to the mantissa and biased exponent. The representation is similar to that of IEEE 754 format i.e., Bias = (2k - 1) because it is %3D used to represent + 0, t oo. Let 4 bit biased exponent and, 7-bit mantissa is placed in 12 bit register as shown below. E (4) Which of the following pattern denote the value 14.25?
Binary 4-bit Asynchronous down Counter and explain how it functions, find real life applications
1. Assuming the full adder drives a load L=1.5, determine the critical path and its corresponding delay.2. Using this full adder to create an 8-bit ripple carry adder, what is the critical path delay of this 8-bit adder? (Assume unconnected ports are driving L=1.5 load)
(a) Determine the worst-case delay of a 16-bit carry select adder. Assume tsetup = tsum = 2, and tcarry = tmux = 1. Compare this with the worst-case delay of a 16-bit ripple carry adder. (b) If each stage has 4 bits, what is minimum number of bits (N) do we need to have, in order for the carry-select adder to start showing less delay (when compared to a ripple-carry adder)? Assume tsetup = tsum = 2, and tcarry = tmux = 1.
What is a transmission gate? Draw its circuit circuit diagram. How does it operate? What is the need for a transmission gate? What is it disadvantage?
a) Design Binary Ripple Counter using D-flipflop. b) Design asynchronous 4-bit UP-Down counter.
1 %9Y li. ln. , D 9:-7 A 2-bit binary comparator designed by using synchronous state machine has two outputs. The outputs are always equal to (00) unless one of the following cases occurs: 1. If the present input value is greater than the previous input value, the first and second outputs are logic "1" and logic "O", respectively. 2. If the present input value is less than the previous input lue, the first and second outputs are logic "O" and logic "1", respectively. How many states are required to draw minimal Mealy state diagram for the aforementioned state machine? * 8. 4 2 7
Using a combination of shift registers and latches explain how a small number ofmicrocontroller I/O pins can be used to read from or write to a large number of digitalsignal lines. Illustrate your answer. What is the main disadvantage of this I/O expansionapproach?