Solve part D The Parallel In / Parallel Out Shift Register.A.Connect the circuit as shown on the next page with the trainer power offSet all the input switches LOW. Turn the trainer power on. All LEDSshould be low. If not, press the PULSE pushbutton until all LEDS areLOW.В.Set the Data inputs B & C to 1. Set the Mode (F) to 1.Press & release the PULSE pushbutton to trigger the Clock pulse.С.What appears at the output LEDS?Enter the following data patternsand record the outputs.InputSwitchesD.14 +5V7495B •24 Bit13 LED10010 >>C •3Parallel In12 LED20110 >>Parallel Out |11 LED31110 >>E •510 LED41111 >>F•6.9.GRD|78Pulse

The Parallel-In Parallel-Out shift register is a type of data storage device. This is commonly…

Enter the following data patterns and record the outputs. Input Switches D. 14 +5V 7495 B • 2 4 Bit 13 LED1 0010 >> C 12 LED2 Parallel In 0110 >> 4 Parallel Out 11 LED3 1110 >> E • 10 LED4 1111 >> F• 6 GRD|7 8 Pulse

Enter the following data patterns and record the outputs. Input Switches D. 14 +5V 7495 B • 2 4 Bit 13 LED1 0010 >> C 12 LED2 Parallel In 0110 >> 4 Parallel Out 11 LED3 1110 >> E • 10 LED4 1111 >> F• 6 GRD|7 8 Pulse

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Subject-power electronic Define A.Delay time B.Rise time C.reverse recovery voltage D.spread time.
A switch that can conduct positive on-state current, and can block positive or negative off-state voltage is called ___. A. voltage-bidirectional two-quadrant switch B. synchronous rectifier C. single quadrant switch D. four-quadrant switch
the controlled signals in control BD are then going to Select one: a. actuators b. sensors C. plant d. controllers the actuator requires a much higher primary voltage than 150v is Select one: O a Capacitive Discharge Ignition (CDI) O b. Inductive (Smart) O C. Peak and Hold O d. Inductive (Dumb)
Answer the following questions (a)What is a clock signal?(b)Differentiate between positive going pulse and negative going pulse?(c) Define leading edge and trailing edge of a pulse?(d)For a positive going pulse, mention the leading edge and trailing edge?(e)For a negative going pulse, mention the leading edge and trailing edge? Please write the answer in short
ASYNCIN Dan Synchronous System CLOCK Figure Q4 (b) The circuit in Figure Q4 (c) consists of edge triggered flipflops. The second flipflop receives the clock signal through a long slow path which results in delay. Answer the following questions: Q1 Q2 IN DaK CLOCKD CLK CLOCK A long, slow path Figure Q4 (c) 林 Define clock skew, Explain with a timing diagram, what problem this circuit might face? What condition it must satisfy to ensure that the intended circuit output is not affected? For the following LFSR circuit in the Figure Q4 (d), let the initial entries of stages R, be S, for 0sisn. Compute the first 12 bit output for the following cases of initial entries: (d) S2 Si So Case 1 Study Pack Practice &A Case 2
a) Figure 3 illustrates a thyristor phase control circuit and associated waveforms. Describe the function of the control element in the circuit towards the output at the load. Identify the best-suited application to describe the control circuit. Lamp Load VAC SCR r 9 8₁ Conduction MM h 18₂ h Gate Trigger Pulse
Why SCR is not preferred as a switching device in the circuit having DC input supply? Explain How to turn ON and turn OFF the SCR when it is working in AC and DC supplies.
15. What is the relationship of the gate pulses to the two thyristors in a full-wave ac phase control circuit? 16. A buck chopper is powered by a 200-V dc power supply. What is the output voltage range of this chopper if the duty cycle can be varied between 30 and 95%?
Gradual change in the measurement output while the measurand remains constant is called:Select one:a. Sensor reproducibleity b. Sensor offsetc.Sensor driftd. Sensor Hysteresis
1. For the ADC0804 used in section 1. the step size can be adjusted by setting the reference voltage on pin 9. When this pin is not connected (as shown in the figure 1 schematic), the reference voltage is the operating voltage Vcc. a) What is the step size for this default setting? b) How can we set the reference voltage on pin 9. to 4 V? c) What would be the step size after changing the reference voltage to 4 V? 2. Determine the analog input that will result in an output code of "10001110". Assume 5 V reference. Show your calculations. 3. What value of the analog input voltage would result in a digital output is 6F (hex)? Assume 4V reference. Show calculations. 4. In section, you used a 8-bit D/A converter. With a reference voltage of 5 V, what voltage does each bit represent in terms of the analog output? Show calculations. 5. For the D/A converter, if the output is 3.62 V, what is the value of the digital input? Show calculations. 6. For the D/A converter circuit shown in Figure 2,…
The p-channel JFET used in Digital technology as_____. a.switch b.rectifier c.invertor d.amplifier
14) An SCS has a unique ability to: A) be turned off only with a pulse B) be turned on or off with a pulse. C) control a PUT. D) All of the