1. For the ADC0804 used in section 1. the step size can be adjusted by setting the reference voltage on pin 9. When this pin is not connected (as shown in the figure 1 schematic), the reference voltage is the operating voltage Vcc. a) What is the step size for this default setting? b) How can we set the reference voltage on pin 9. to 4 V? c) What would be the step size after changing the reference voltage to 4 V? 2. Determine the analog input that will result in an output code of "10001110". Assume 5 V reference. Show your calculations. 3. What value of the analog input voltage would result in a digital output is 6F (hex)? Assume 4V reference. Show calculations. 4. In section, you used a 8-bit D/A converter. With a reference voltage of 5 V, what voltage does each bit represent in terms of the analog output? Show calculations. 5. For the D/A converter, if the output is 3.62 V, what is the value of the digital input? Show calculations. 6. For the D/A converter circuit shown in Figure 2, If ‘V+' reference was changed to +10 V What will be the output voltage for the digital input value of 200 (decimal)?

1. For the ADC0804 used in section 1. the step size can be adjusted by setting the reference voltage on pin 9. When this pin is not connected (as shown in the figure 1 schematic), the reference voltage is the operating voltage Vcc. a) What is the step size for this default setting? b) How can we set the reference voltage on pin 9. to 4 V? c) What would be the step size after changing the reference voltage to 4 V? 2. Determine the analog input that will result in an output code of "10001110". Assume 5 V reference. Show your calculations. 3. What value of the analog input voltage would result in a digital output is 6F (hex)? Assume 4V reference. Show calculations. 4. In section, you used a 8-bit D/A converter. With a reference voltage of 5 V, what voltage does each bit represent in terms of the analog output? Show calculations. 5. For the D/A converter, if the output is 3.62 V, what is the value of the digital input? Show calculations. 6. For the D/A converter circuit shown in Figure 2, If ‘V+' reference was changed to +10 V What will be the output voltage for the digital input value of 200 (decimal)?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Apply the junction rule to junction b in Figure. Is any new information gained by applying the junction rule at e? (In the figure, each emf is represented by script E.)
What is the significance of Ohm's law in electronic engineering?
In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.
Explain in detail this sma connector
Describe the purpose of a PV and PQ curves. Draw the curves and explain its position (stability & unstable areas) Describe the difference between each curve by reference to the curves and explain when each one would be used
What is a comparator IC, and how do we use it?
What are the different types of IC voltage regulators? Explain each one work's.
Draw a figure of bridge type full wave rectifier power supply. Draw the input and output signals for each layer and briefly explain the purpose of each layer.
Do calculation. This is not a simulation problem
What are IC Voltage regulators? State the different IC voltage regulators and its operation.
Convert a dc voltage Q7)------ from one level and a certain polarity to a dc voltage of another level and in some applications to another polarity. Oa. DC-AC Converter Ob. AC-AC converter Oc. DC Chopper Od. AC-DC rectifier