Replace the two forces shown with an equivalent force-couple system with the force acting at O.

Q: Air enters the turbine at 1 MPa and 327 degree* C with a velocity of 100 m/s and exits at 100 kPa an...

A:

Q: The walls of the refrigerated storage room are 10 m long and 3 m high and constructed with 100 mm co...

A: Given data:

Q: Determine the dynamic viscosity in terms of Ns/m2 of a fluid having kinematic viscosity 0.036 m2/sec...

A: Kinematic viscosity=0.036 Specific gravity=0.9

Q: An ice cube (mass 30 g) at 0°C is left sitting on the kitchen table, where it gradually melts. The t...

A: given:  mass of ice cube  m=30gT2=250CT1=00C  

Q: A 9.1kg body is suspended from a spring of constant k = 2.0kN/m. At time t 0, it has a downward velo...

A: Mass of the body, m=9.1 kg Spring constant, k=2 kN/m. Here, frequency of the system is given by, f=1...

Q: PROBLEM 1. The dimensions of a bar made of a 2024-T6 aluminum alloy and the loads acting on it are s...

A:  

Q: A 5-kg model rocket is launched vertically and reaches an altitude of 100 m with a speed of 40 m/s a...

A:

Q: When a foreign atom replaces the parent atom in the lattice position is Self Interstitial atom Sel...

A: The self interstitial defect is described as a kind of interstitial defect that consists of the atom...

Q: A steel shaft ABC connecting three gears consists of a solid bar of diameter d between gearsA and B ...

A: Given Data: The value of T1 = -240 N-m. The value of T2 = 540 N-m. The value of T3 =- 300 N-m. The ...

Q: please include sufficient explanation in the answers. thx

A: Given data: The mass of block is M = 50 kg. The height from which the block is dropped is h = 2 m. ...

Q: A flat bar of width b= 60 mm and thickness t is loaded in tension by a force P (see figure). The bar...

A:

Q: A 1.25 in.-square steel punch is to push through an aluminum plate that is supported on a die, thus ...

A: Given The side of the square steel punched part is s=1.25 in. The allowable compressive strength is...

Q: answer the question in the picture

A:

Q: A freezer with dimensions of 4 m wide, 7 m long and 3 m high is under construction. The walls and ce...

A: Given, Conductivity of stainless steel (K1)=15W/m°C Conductivity of foam (K2)=0.036W/m°C Conductivit...

Q: The chief engineer at a university that is constructing a large number of new student dormitories de...

A: Mass flow rate = 10 kg/ min L= 1 m Di = 50 mm Th,I = 38 °C Tc,I = 10 °C hh = 10,000 W/m2 d= 10 mm hc...

Q: A machine of mass 500kg is mounted through four mounting pads that exhibit linear elasticity and vis...

A: Given data: The mass of the machine, m = 500 kg. The distance moved by the pad, x = 10 mm. The damp...

Q: A bar of titanium alloy of length 120mm and square cross – section, 7.5mm x 7.5 mm, is pulled axiall...

A: Given, Length of the bar, L=120 mm Cross-section of the bar, 7.5×7.5 mm2 Axial force on bar, P=15 kN...

Q: In a tensile test on a specimen of black mild steel of 12 mm diameter, the following results were ob...

A: Consider the given data. Breaking stress is the ration of the load corresponding to fracture of the ...

Q: the figure shows a tank within a tank, each containing air. pressure gage a is located inside tank b...

A: FIND:      The absolute pressure of air in tank B and in tank A, both in bar ANALYSIS:      pgauge,A...

Q: A brass specimen of the circular cross-section is fractured at 159 kN force and the final length of ...

A: Given data: Force = 159 kN                     Final length of specimen = 51 mm                    F...

Q: What are the key challenges of Kia picanto (Car)?

A: There are mainly issues related to the economy of the car. Due to lots of competitors in the market ...

Q: A slider-crank mechanism is required to do the following crank angle-slider position coordination. ...

A: given    Position-1   0°  12 cm  Position-2      90°  10 cmcrank speed 1 rad/svelocity of slider=5cm...

Q: Chapter Six Vibrations b) Find the differential 2a equation for small oscillations C in terms of (0 ...

A: Given data: Beam with springs and damper attached as shown above   To determine: Differential equati...

Q: b) Write down the parts of an universal chuck.

A:

Q: a) An anemometer for measuring the wind speed consists of three thin, hemispherical shells of mass M...

A: Given data: Figure as shown above with relevant details   To determine: Mass moment of inertia about...

Q: Steam at 150 ° C flows in a pipe having an inner radius of 50 mm and an outer radius of 55 mm. The ...

A:

Q: A rigid tank of volume 0.5 m^3 is initially evacuated.a tiny hole develops in the wall, and air from...

A:

Q: A 328-N force is applied at A as shown. Determine the moment of the force about D.

A: Draw the free body diagram:      

Q: When a tensile load of 20kN is applied to a rod of length 5 cm changes its length by 1 mm. The strai...

A:

Q: 1. Use the integration method to determine the slopes and deflection at points B and C of the beam b...

A: givencantilever beam P=270kNload intensity w=45kN/mE=200GPaI=1665×106 mm4=1665×10-6 m4

Q: Unit kg of steam is heated reversibly at constant pressure of 2.5MPa, a temperature of 252.3C and dr...

A: Given: The mass of the steam is m=1 kg, The initial pressure is P1=2.5MPa=2500 kPa, The final press...

Q: The following data are obtained from a tensile test of an aluminium specimen. - The load at the yiel...

A: Given data: The load at the yield point is Fy = 147 kN.  The length of the specimen is initial leng...

Q: A small, electric car (Fig. P13-48) has a maximum constant acceleration of 1 m/s2, a maximum constan...

A: Given, Constant acceleration a1= 1m/s2 Constant deceleration a2=-2m/s2 Top speed = 80km/hr or 22.222...

Q: Answer in picture containing the question. Kindly before submitting the solution.

A: Given:When the block is released the cord is straight. Neglect friction To find: The acceleration wh...

Q: A generating station is to give a power output of 200 MW. The superheat outlet pressure of the boile...

A:

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.