Your reading material states that the two MAIN factors that determine the amount of current that will flow during a short circuit condition are 8. circuit amperage and circuit voltage circuit amperage and circuit impedance circuit impedance and power factor circuit voltage and circuit impedance a. b. С. d.

Your reading material states that the two MAIN factors that determine the amount of current that will flow during a short circuit condition are 8. circuit amperage and circuit voltage circuit amperage and circuit impedance circuit impedance and power factor circuit voltage and circuit impedance a. b. С. d.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.4MCQ

See similar textbooks

Similar questions

Power factor correction is usually done by adding _________ to the load circuit.Select the correct response:a. switchb. capacitorc. inductive loads
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
What is a microgrid?
Two sinusoidal currents are given by i1, and i2. The absolute phase difference between them is ___ degrees.
two generators supplying a load. Generator I has a no-load frequency of 62.5 Hz and a slope Sp1 of I MW/Hz. Generator 2 has a no-load frequency of 62.0 Hz and a slope sp2 of I MW/Hz. The two generators are supplying a real load totaling 2.5 MW at 0.8 PF lagging. (a) At what frequency is this system operating, and how much power is supplied by each of the two generators? (b) Suppose an additional I-MW load were attached to this power system. What would the new system frequency be, and how much power would Gl and G2 supply now? Generator 1 VT V2 Generator 2 VTí KVAR KVAR
please solve for nodal stress method. (if it is possible to apply supernodes)
7. In the circuit below write the loop equations and set up (not solve) the matrix equation for the load current. Wiso 150 75 28 100
2. A single-phase are distributor AB is fed from end A and has a total impedance of (0.3-0.3) ohm. At the far end, the voltage V-240V and the current is 100A at a p.f. of 0, 8 lagging. At the mid-point M. a current of 100 A is tapped at a p... of 0.6 lagging with reference to the voltage V_{M} at the midi-point. Calculate the supply voltage V Lambda j sending current I_{N} and the phase angle between V_{A} and V_{E}
What are two ways of reducing Z0? (last part of the question)
A three-phase balanced load of 15A per phase is supplied by a steel wire armoured cable with a c.s.a. of 2.5mm². The voltage drop for this cable is 15mv/A/m and the circuit is 40m long. Calculate the voltage drop in the cable.
How can I compute and get the values of branch currents (Iab, Iac, Ibc, Ibd, Icd and Ica) and the algebraic sum of the potential difference for electrical loops (abca, abdca, acda, abcda and acbda) by using Kirchhoff's voltage and current law (KVL and KCL) equations?
A- A 3-ph, double circuit O.H.T.L, 320 kV, 340 km, 50 Hz has a configuration as shown in the figure below where each phase in the double circuit has a double bundle with a spacing of d cm between the two conductors in the bundle where d is the last two digits (from right) of your registration number (i.e for the student that has a registration mumber 202112396, d= 96). Each conductor in the bundle has a diameter of 0.135 ft and a geometric mean radius (Ds = 1.6 cm). Calculate: 1- Inductance per phase per km. 2- Total inductive reactance. 3- This T.L. is required to supply 240 MVA at 0.86 lag P.f. at 320 kV, assuming that this load is divided equally between these two circuits, find the voltage drop across this T.L (ignore capacitive effect in the calculation). 4- What may happen if we replace the location of a' and c' bundles. Discuss your answer. 5- Suggest a way to ređuce the value of the inductance. Verify your suggestion. -8 m 3m 3m 8 m 11 m