Homework Help is Here – Start Your Trial Now!
Engineering
Civil Engineering
You pass by a building site and see a crane that lifts loads to upper floors of a building under construction. You wonder about the magnitude of the forces that support the beam of the crane. You snap a photograph of the crane with your smartphone. Back at home, you make a drawing of the crane from your photo. Your drawing is shown in the following figure. XCM You estimate the lengths d and f by measuring the distance between floors on a point of the building the same distance from your smartphone as the crane and using that distance as a scale for the drawing. This tells you that d = 1.00 m and t = 6.00 m. You have drawn the force vector for the gravitational force on the beam of the crane, but then you realize you don't know where the center of mass of the beam is located. You run back to the construction office and explain your interest. You ask the construction foreman about the crane, and he tells you that the crane itself has a mass of m₁ = 2,875 kg and the load it was lifting when you took the photograph has a mass of m₂ = 11,450 kg. You then ask the foreman about the location of the center of mass of the beam. Amused by your interest, he consults his documents and finds that the center of mass of the crane is located XCM = 2.00 m horizontally to the right of point A. He also tells you that the pin at A is on a bearing and essentially frictionless, and the point B against which the crane pushes is smooth. Thanking the foreman and running home, you sit at your desk and determine the forces on the crane at points A and B. N

You pass by a building site and see a crane that lifts loads to upper floors of a building under construction. You wonder about the magnitude of the forces that support the beam of the crane. You snap a photograph of the crane with your smartphone. Back at home, you make a drawing of the crane from your photo. Your drawing is shown in the following figure. XCM You estimate the lengths d and f by measuring the distance between floors on a point of the building the same distance from your smartphone as the crane and using that distance as a scale for the drawing. This tells you that d = 1.00 m and t = 6.00 m. You have drawn the force vector for the gravitational force on the beam of the crane, but then you realize you don't know where the center of mass of the beam is located. You run back to the construction office and explain your interest. You ask the construction foreman about the crane, and he tells you that the crane itself has a mass of m₁ = 2,875 kg and the load it was lifting when you took the photograph has a mass of m₂ = 11,450 kg. You then ask the foreman about the location of the center of mass of the beam. Amused by your interest, he consults his documents and finds that the center of mass of the crane is located XCM = 2.00 m horizontally to the right of point A. He also tells you that the pin at A is on a bearing and essentially frictionless, and the point B against which the crane pushes is smooth. Thanking the foreman and running home, you sit at your desk and determine the forces on the crane at points A and B. N

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)
Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)
5th Edition
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Saeed Moaveni
Chapter10: Force And Force-related Variables In Engineering
Section: Chapter Questions
Problem 29P: A structural member with a rectangular cross section as shown in the accompanying figure is used to...
See similar textbooks
icon
Related questions
Question
You pass by a building site and see a crane that lifts loads to upper floors of a building under construction. You wonder about the magnitude of the forces that support the beam of the crane. You snap a photograph of the crane with your smartphone. Back at home, you make a drawing of the crane from your photo. Your drawing is shown in the following figure. m M B *CM You estimate the lengths d and I by measuring the distance between floors on a point of the building the same distance from your smartphone as the crane and using that distance as a scale for the drawing. This tells you that d 1.00 m and t = 6.00 m. You have drawn the force vector for the gravitational force on the beam of the crane, but then you realize you don't know where the center of mass of the beam is located. You run back to the construction office and explain your interest. You ask the construction foreman about the crane, and he tells you that the crane itself has a mass of m₁ = 2,875 kg and the load it was lifting when you took the photograph has a mass of m₂ = 11,450 kg. You then ask the foreman about the location of the center of mass of the beam. Amused by your interest, he consults his documents and finds that the center of mass of the crane is located XCM = 2.00 m horizontally to the right of point A. He also tells you that the pin at A is on a bearing and essentially frictionless, and the point B against which the crane pushes is smooth. Thanking the foreman and running home, you sit at your desk and determine the forces on the crane at points A and B. i+ ₁) N i+ N
Transcribed Image Text:You pass by a building site and see a crane that lifts loads to upper floors of a building under construction. You wonder about the magnitude of the forces that support the beam of the crane. You snap a photograph of the crane with your smartphone. Back at home, you make a drawing of the crane from your photo. Your drawing is shown in the following figure. m M B *CM You estimate the lengths d and I by measuring the distance between floors on a point of the building the same distance from your smartphone as the crane and using that distance as a scale for the drawing. This tells you that d 1.00 m and t = 6.00 m. You have drawn the force vector for the gravitational force on the beam of the crane, but then you realize you don't know where the center of mass of the beam is located. You run back to the construction office and explain your interest. You ask the construction foreman about the crane, and he tells you that the crane itself has a mass of m₁ = 2,875 kg and the load it was lifting when you took the photograph has a mass of m₂ = 11,450 kg. You then ask the foreman about the location of the center of mass of the beam. Amused by your interest, he consults his documents and finds that the center of mass of the crane is located XCM = 2.00 m horizontally to the right of point A. He also tells you that the pin at A is on a bearing and essentially frictionless, and the point B against which the crane pushes is smooth. Thanking the foreman and running home, you sit at your desk and determine the forces on the crane at points A and B. i+ ₁) N i+ N
Expert Solution
trending now

Trending now

This is a popular solution!

steps

Step by step

Solved in 3 steps with 2 images

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Knowledge Booster
Work and energy
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.
Similar questions
  • SEE MORE QUESTIONS
Recommended textbooks for you
Engineering Fundamentals: An Introduction to Engi…
Engineering Fundamentals: An Introduction to Engi…
Civil Engineering
ISBN:
9781305084766
Author:
Saeed Moaveni
Publisher:
Cengage Learning
SEE MORE TEXTBOOKS