You are free to asuume anything that did not mentioned You may use suitable type of gears, bearings and belt in your design. Show all calculationand assumptions you made in your design. Your design can be divide in below items:The typical gearbox will involve 4 subsystems:a) Gearing (4 gears),b) Bearings,c) Shafting El motor₁,M₁#(a)c = const.I₁+6 inConveyorGearboxراونPower (electric motor) to be delivered: 20 hpInput speed of gearbox: 0₁ = 1750 rpm.Output speed of gearbox: 02= 80-90 rev/min.Speed of the Conveyor: 0340-45 rev/min.Usually low shock levels, occasional moderate shock.1₂Input and output shafts extend 4 in outside gearbox.Maximum gearbox size: 15-in x 15-in base, 22-in height.Output shaft and input shaft of gearbox is in-line.Gear and bearing life. 10 000 hours; infinite shaft lifec=const.c = const.(b)The schematic diagram above shows a uniform load belt conveyor is driven by an electricmotor. Power from the motor is transmitted through a Gearbox (Fig. a) and belt drive (Fig.b). You are required to design and analyses the detail of gearbox and belt system.Information relating to the system is given in the below:Belt (V-belt)driveA subset of the pertinent design specifications that will be needed for this part of the designare given here.

You may use suitable type of gears, bearings and belt in your design. Show all calculation and assumptions you made in your design. Your design can be divide in below items: The typical gearbox will involve 4 subsystems: a) Gearing (4 gears), b) Bearings, c) Shafting

You may use suitable type of gears, bearings and belt in your design. Show all calculation and assumptions you made in your design. Your design can be divide in below items: The typical gearbox will involve 4 subsystems: a) Gearing (4 gears), b) Bearings, c) Shafting

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 1000 RPM speed reducer and 12KW power drives a conveyor belt at 400 RPM. the distance between the centers is approximately 800mm. Select a suitable chain for transmission, as follows:1) Solicitation with moderate shock, abnormal operating conditions, operating 24 hours a day.
Q2) A flat belt drive system is to be) designed for an application in which the input shaft speed is 1725 rpm, the driven shaft speed is to be approximately 960 rpm, and the power to be transmitted has been estimated as 2.5kW. The driven machine has been evaluated and found to have characteristics of moderate shock loading during operation. The desired center distance between driving and driven pulleys is approximately 0.5m. The recommended pulley diameter is 110mm. The belt is made of polyamid with density of 0.95g/cc and the coefficient of friction is 0.8. The limiting design-allowable tension per unit width for the polyamide is 613ON/m.a. If 5mm-thick belt material were chosen for this application, what belt width would be required?b. What initial tension would be required for ?proper operation
Calculation for drive system and rack/spur gear of a crane. System needs to able to climb an incline of 12.457 beam tilt from horizontal With a payload weight of 27,500 lbs. using a 2 hp motor, 1725 rpm, 60 hz Gear reducer with 8.5 output rpm, ratio 204.75 Drive speed of 2.238 in/s Tooth force of 5931.798 lbf Rack - 20 PA, 2.5" face width, 1.5" thickness, 6' length, diametral pitch 5 in, 1018 steel Spur gear - 2.5" face width, diametral pitch 5 in, 20 PA, 30 teeth, 6.4 OD, 6 PD, 1144 steel Will this system work? If not, what material/gear reducer will work? Also, what is the max angle a 10 ft-lb electrical brake can statically hold a 27,500 lbs payload?
power (N)=9.9kw Input speed (n1)=2350rpm Distance between centers (a)=168mm Total distance between Ave B bearings=440mm module(m)=3mm question 3 Calculate the power on the output shaft since there is 3% loss in gears in gearboxes, rolling bearings in support bearings (2% loss in a pair of bearings) and sealing element spring seal (4% loss in a pair of sealing elements).
Engine Type Four cylinder Four stroke MPFI petrol engine(Maruti Zen), Bore: 0.072 m, Stroke: 0.061m Capacity: 993 cc, Power: 60 HP at 6000 rpm, Torque: 78.5 Nm at 4500 rpm and Compression Ratio :9.4:1. Explain how to calculate :- (1) Mechanical Efficiency (2) Brake Thermal Efficiency (3) Indicated Specific Fuel Consumption
Seatwork No. 1 An SI I-2 square engine operates on a 2-stroke cycle at 2400 rpm. The average piston speed is 15 m/se and the no. of piston action is 2. When the piston is at its maximum position the remainder volume is 0.005 Liters. Determine: a. Volumetric displacement per unit time for all cylinders (m³/sec) b. Compression ratio c. Volume at Bottom Dead Center (m³)
480 ft-lbf First Gear (2.66) Final Drive (3.42) Figure 2 - Corvette Z06 and its transmission schematic. You start by measuring the 60-0 mph braking performance, which is accomplished along 30.56 m. The test weight (including the driver) was found to be 1510.5 kgf. Peak torque (@4800 rpm) 1st gear reduction Axle Torque Thrust Force After the braking test, you are asked to determine the maximum acceleration in the first gear. Consulting the manufacturer, you find out the following technical data: Final drive (differential) reduction Rolling radius of the rear tyres % weight on the rear tyres Table 1 - Technical data for the Corvette Z06 480 lbf-ft 2.66 3.42 0.327 m 65% 1) Assuming the maximum traction capacity of the tyres has been determined in the braking test, CALCULATE the maximum traction generated by the rear tyres in first gear. CALCULATE the available thrust force (i.e. traction) from the torque on the wheels.
The client requires a single step up spur gearbox to transmit a 10kW power from a shaft rotating at 1000rpm, while the output speed must be 1700rpm.The material for gear and pinion is 817M40 and 665M13, respectively. The pinion has 20 teeth. State formula and standardd relevant to the single step up spur gearbox design
A gasoline engine working on four-stroke develops a brake power of 20.9 kW. A Morse Test was conducted on this engine and the brake power (kW) obtained when each cylinder was made inoperative by short circuiting the spark plug are 14.9, 14.3, 14.8 and 14.5 respectively. The test was conducted at constant speed. Find the indicated power, mechanical efficiency and bmep when all the cylinders are firing. The bore of the engine is 75 mm and the stroke is 90 mm. The engine is running at 3000 rpm.
vertical single cylinder four stroke diesel engine has a bore = 87.5 mm and stroke = 110 mm respectively. It is water cooled and develops a torque of 16.25 N-m when running at 1465 rpm , with fuel consumption time for 10 cc as 28.0 sec. find brake specific fuel consumption? , Assume the specific gravity of fuel to be 0.82.
The following data are the results on a test of an Otto cycle engine: Torque= 1300N-m. Indicated mean effective pressure= 800kpa, Fuel consumption=0.004kg/sec Fuel heating value=43,816KJ/kg Bore and stroke= 30cm x 32cm Speed= 400rpm. Calculate the brake mean effective pressure in kpa.
The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.4;working speed= 600 rpm; friction surface number= 2; required closing force= 712 N, clutch outerIf diameter = 300 mm, clutch inner diameter = 120 mm, how much power is transmitted?