You just landed a job at an Amazon facility and have been tasked withdesigning a pulley system to move crates across the warehouse floor.Your predecessor chose a motor that is able to exert a force of F=14s + 200 N where s is the displacement of the crate in meters. Unfortunately, your boss won't give you enough of a budget topurchase wheels, so the crates will be pulled across the floor. Youestimate the coefficient of kinetic friction between the crate and thefloor to be μ = 0.25. If a 24-kg crate is initially at rest, a. Determine and plot the acceleration and velocity of the crate asfunctions of position. b. How would you solve for position as a function of time? Set-up(but you don't need to solve) the equations needed to findposition as a function of time. Hint: start with v = ds/dt

You just landed a job at an Amazon facility and have been tasked withdesigning a pulley system to move crates across the warehouse floor.Your predecessor chose a motor that is able to exert a force of F=14s + 200 N where s is the displacement of the crate in meters. Unfortunately, your boss won't give you enough of a budget topurchase wheels, so the crates will be pulled across the floor. Youestimate the coefficient of kinetic friction between the crate and thefloor to be μ = 0.25. If a 24-kg crate is initially at rest, a. Determine and plot the acceleration and velocity of the crate asfunctions of position. b. How would you solve for position as a function of time? Set-up(but you don't need to solve) the equations needed to findposition as a function of time. Hint: start with v = ds/dt

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Design a quick return mechanism with 120 cm stroke, time of forward stroke is 1.2s, return stroke time is 0.4s, fixed link length of 25 cm and driving crank length of 40cm. Determine a.Range of values of L2 b.a and B cộ1 and 2 d.Actual value of L2
Q3. Audi’s design of their R8 model is designed in order to have the engine in the rear of the car with the following schematic of their mechanical power transmission. The engine is connected to the gearbox, where gear change occurs and then a driveshaft is used to transfer an equal ratio of power balancing the rear and front wheel power output thus referring to it as an all-wheel drive. The vehicle has been modified by a customer thus resulted to no power transfer to the front wheels although the rear wheels still have the same power output. Using your knowledge, DEFINE and JUSTIFY the possible reasons of why the front drive isn’t functioning. What are the solutions to this fault?
1. Design a crank-rocker linkage that will move the rocker link between two extreme positions 45 de apart. The rocker should take twice the time to moving in one direction that it takes moving in the other. somyb\\; eqrad no malieb uroy dont elle est sor oldnoba mare ono mol foque (do iliw now wodor 00. aasbois.oved nov 2. If the fourbar linkage designed in question 1 is non-grashof, list two ways in which you would alter the design so that the crank is able to rotate.
calculate the power transmitted and the rotational speed in r/min of the small pulley of a belt drive where the diameter of the deriven pulley is 275 mm and rotates at 750 r/min. the driving pulley size is 125 mm. the tension is the tight side of the belt is 500 N, with the tension ratio between the tight and slack side side being 4.33:1
Suppose the four legs of Sitting on abe are Chair You identical this Scm springs. when you on Chair the chau's downwatd. what Constant of each is spring Spring? D Now Suppose that the Seae has only One leg. This leg is made by. tonnectin all the four spings in line when you sit it, the chair goes Scm downward. what is the Spring a on Constant of each spring ? (note): You owń uweight / mass for calculation' if you want to get numericlal Values Should use your as answer? Shot on vivo S1 00 AI Triple Camera
. A pulley used to transmit power by means of ropes has a diameter of 3.5 m and has grooves of 45° angle. The angle of contact is 160° and coefficient of friction between the ropes and groove sides is 0.3. The maximum possible tension in the rope is 1000 N ad the mass of rope is 1.5 kg per metre length. What is the speed of the pulley in rpm and the power transmitted if the condition of maximum power prevail? 10
A1 A grinding wheel used in machine shop needs to be analyzed in terms of its suitability for a specific grinding task. Find 1. Accelerating torque produced by the grinding wheel II. Increase in angular momentum of the grinding wheel II. Increase in Kinetic energy of the grinding wheel. Assume the following data Suitable mass of the grinding wheel. Suitable radius of grinding wheel. Select any two Speeds between range 1000 – 3000 rpm. Consider 20 seconds time gap between two speeds selected. 1. 2. 3. 4. Justify your data assumptions.
Aim: To conduct a full kinematic analysis and calculate dynamic reaction forces in a linkage mechanism, calculate instantaneous torque, required to drive the mechanism and to present the results of the case study in a clear reporting format. Introduction: Figure 1 shows a pumpjack operating at an oil well. Its representation as a linkage is also shown in Figure 1. The pumpjack is driven by a motor attached to crank OA. A constant torque T is applied to the crank and the crank rotates at a constant angular velocity ???. A force P is applied vertically downwards at the end of the walking beam BD, which has its centre of mass at point G. To design the mechanism, a careful kinematic analysis of the mechanism needs to be conducted. To avoid mechanical failure and to provide adequate support to the mechanism, the engineer needs to analyse the reaction forces in the joints. Masses of links OA and AB are assumed to be smaller in comparison with the mass of BD and are ignored in the analysis.…
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
The weight of the wheel tractor in Problem 1 is 30 tons and the weight on the drivingwheels is 50% of this weight. What is the maximum available rimpull if thecoefficient of traction is 0.25?
You’re using a system of multiple simple machines to move a 1500 N load up a height of 2 meters. You have a wheel barrow which is a combination of a lever and a wheel/axle, and you’ll be using a ramp (inclined plane).a. If you want to apply a maximum effort force of 50 N – what does the actual mechanical advantage of the compound machines need to be? b. The wheel barrow in problem above has the following dimensions Wheel axle radius: 7.5 cmWheel outer radius: 25 cmLoad distance to fulcrum: 55 cm Handle distance to fulcrum: 200 cmWhat is the wheel barrow’s total ideal mechanical advantage? c. Due to a rusty wheel axle, the wheel-barrow in problem above only has an efficiency of 65%. What is the actual mechanical advantage of the wheel barrow?
You have a lever, 2m on each side, and four masses: 5kg, 10kg, 15kg and 20kg. You will place the blocks at different positions on the lever such that the two sides balance. Place each block a unique distance from the fulcrum. Use a torque balance to prove the system will not move.