You just finished plating your electroporatio products on your YPD-Zeocin plate and you think you did everything perfectly but you come back the folloeing week and have zero colonies. Which of the following could be the reason for the absence of colonies? A) You centrifuged your electroporated cells for 30 sec at 16,000 rpm instead of 4,000 rpm before plating them B) You added sorbitol+YPD to your cells thirty minutes after pulsing your cells C) The Zeocin had not been added to the plates when they were made. D) All of the above E) Both a and b only

You just finished plating your electroporatio products on your YPD-Zeocin plate and you think you did everything perfectly but you come back the folloeing week and have zero colonies. Which of the following could be the reason for the absence of colonies? A) You centrifuged your electroporated cells for 30 sec at 16,000 rpm instead of 4,000 rpm before plating them B) You added sorbitol+YPD to your cells thirty minutes after pulsing your cells C) The Zeocin had not been added to the plates when they were made. D) All of the above E) Both a and b only

Curren'S Math For Meds: Dosages & Sol

11th Edition

ISBN:9781305143531

Author:CURREN

Publisher:CURREN

Chapter10: Reconstitution Of Powdered Drugs

Section: Chapter Questions

Problem 17SST

See similar textbooks

Similar questions

Blood agar is often used to observe changes in the appear-ance of the agar around the colonies growing on this medium.This medium could then be called:(a) Selective(b) Designated(c) Differential(d) Defined(e) Exact
There are two cultures of yeast cells in the pictures, one has been incubated for 6 hours and one has been incubated for 24 hours. After a 10x dilution by taking 100µl of each culture and adding it to 900 µl water in a microcentrifuge tube and 100µl sample from the tube was taken to view in the counting chamber. a) Count the total number of yeast cells for each culture respectively b) Calculate the concentration and density of yeast cells for each culture respectively
You are given a 1 gram soil sample of unknown bacterial load. After doing 10-fold serial dilutions of the soil in sterile water, 100 uL volumes are taken from each dilution for preparation of pour plates. Following incubation, each half of the 10-8 plate has 46 colonies.a) What was the dilution factor?b) How many bacteria were present in the soil?2. Staphylococcus aureus divides every 20 minutes. A culture begins with 10 bacterial cells.a) After 5 hours, how many generations have occurredb) After 5 hours, how many bacteria are present?3. How many milliliters would you need to prepare a 10-2 dilution from a 10ml starting culture?
N Please observe the following cells that have been Gram stained. "* 3 E ER $ JO 4 R % 5 6 F G & Y I U 8 00
You aseptically transfer 1 mL of your original liquid culture into 99 mL of sterile water. You then repeat this procedure two more times. What is the final dilution factor of this serial dilution? O 1) 10-4 O 2) 102 O 3) 10-6 4) 10-2 O 5) 104
Prior to subculture, Tifa used a hemocytometer to count her HepG2 cells cultured on a T-25 flask. After trypsinization, she prepared her cells by mixing 50 µL of the cell suspension with 50 μL of 0.4% trypan blue. Her observation under the microscope is as shown below: 1 (1) (ii) 3 (iii) 2 (iv) 4 Note: Count cells on the four labelled squares. Include cells touching the line on top and left. 18P 06. ¿66 Ⓡ Determine the number of viable and dead cells from her observation. What is the percentage of viability of this culture? Show your calculations in detail. Calculate the concentration of viable cells per mL in the original culture. Show your calculations in detail. Based on your understanding of cell culture, do you think she should proceed with subculture? Justify your answer.
The thermal death point is best described as:(a) The highest temperature that will support growth of amicrobial culture(b) The length of time required for killing 100% of mi-crobes in a 24-hour culture that is heated to 100°C(c) The temperature at which a previously growing 24-hourculture will begin to die(d) The temperature at which 100% of the microbes in a24-hour culture will be killed in 10 minutes
You are added 60mL of soil slurry to 540mL of sterile water. You can transferred 1000uL of that dilution to 9 mL of water. You then prepared a 10-7 dilution from that tube. You finally transfer 1 uL of that to a TSA plate. After 48 hours, you counted 32 colonies on quarter of the plate. (A) How many cells/mL were present in the original soil sample? (B) How many colonies would be present on the plate if you would have plated 1mL of the last sample? (C) How many milliliters would you need to prepare a 10-4 from 100uL of sample?
Using your fingers, you are asked to aseptically touch the surface of a sterile agar plate. Illustrate the possible result from this step if your fingers are (a) unwashed – touched various things prior to placing on agar surface, and (b) washed with soap or disinfected with 70% alcohol. Describe the relative abundance of microbial growth observed on the plates. List and draw the possible characteristics of an isolated bacterial colony that can be observed based on type of (a) margin, (b) elevation, (c) texture, and (d) optical property.
What would your final dilution be if you transferred 0.1 mL of a 10-6 dilution to a sterile petri dish and then added molten agar to make a pour plate? O 1) 106 O 2) 10-7 O 3) 107 O4) 4) 10-5 O 5) 10-6
Two dyes wereplaced in an agar gel. Which dye migrated through thegel faster? Why? Explain in brief simply terms
Why is washing with Hank’s balanced salt solution with 0.5% antibiotic-antimycotic done for Splenocyte Preparation?