You have 100 mL of a solution of benzoic acid in water; the amount of benzoic acid in the solution is estimated to be 0.30 g. The distribution coefficient of benzoic acid in diethyl ether and water is approximately 10. Calculate the amount of benzoic acid that would be left in the water solution after four 20-mL extractions with ether. Do the same calculation using one 80-mL extraction with ether to determine which method is more efficient.

You have 100 mL of a solution of benzoic acid in water; the amount of benzoic acid in the solution is estimated to be 0.30 g. The distribution coefficient of benzoic acid in diethyl ether and water is approximately 10. Calculate the amount of benzoic acid that would be left in the water solution after four 20-mL extractions with ether. Do the same calculation using one 80-mL extraction with ether to determine which method is more efficient.

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter13: The Chemistry Of Solutes And Solutions

Section13.7: Colligative Properties Of Solutions

Problem 13.17CE

See similar textbooks

Similar questions

In 6.75g of distillate >130C. After performing all necessary GC calculations, it is determined that this sample is 75.9% isopentyl acetate. What qas the actual mass(g) of isopentyl acetate that was actually in this sample? Answer to 2 decimal places
A reagent bottle contains 250 cm3 of 0,4 mol.dm–3 oxalic acid(C2O4H2) solution. Calculate the mass of pure oxalic acid thatmust be dissolved in this solution so that its new concentration is 0,6 mol.dm–3. Assume that the volume of the solution remainsconstant
You are given an 18% solution of sodium imidazole. What mass of imidazole (in g) would be in 20 mL of this solution? a. You need to use the sodium imidazole stock solution from Q11 to make a dilute imidazole solution (final volume 180 mL) at a final concentration of 0.2 M. The molecular weight of imidazole is 90 g/mole. What volume of imidazole stock would you use (mL)? b. You need to use the sodium imidazole stock solution from Q11 to make a dilute imidazole solution (final volume 180 mL) at a final concentration of 0.2 M. The molecular weight of imidazole is 90 g/mole. What volume of water would you add (mL)?
A 10.00 ml sample with an unknown concentration of KNO3 was studied at 60° C. If an additional 2.4 g of KNO, were added to reach saturation. What was initial concentration of Q3 KNO, in M.
STANDARDIZATION OF NAOH SOLUTION A 0.4047 g sample of primary standard grade potassium hydrogen phthalate (MM = 204.23) was dissolved in distilled H2O. The solution required 22.42 mL of the NaOH solution to reach the phenolphthalein end point. a.) Calculate the number of mmoles of KHP. b.) How many moles of NaOH will react with the KHP dissolved in water? c.) Calculate the molarity of the NaOH solution.
The density of methylene chloride is 1.33 g/mL. A mixture of an organic acid, an organic base and a neutral organic compounds is dissolved in methylene chloride as the first step in a liquid-liquid extraction. Which layer is the methylene chloride? - upper layer lower layer
cium chloride per liter. Express the centration in terms of milliequivalents of calcium chloride (CaCl2-2H20-m.w 147) per liter. con- 27. How many milliequivalents/of potassium would be supplied daily by the usual dose (0.3 mL three times a day) of saturated potassium iodide solution? Saturated po- tassium iodide solution contains 100 g of potassium iodide per 100 mL.oluce 28. An intravenous solution calls for the addi- tion of 25 mEq of sodium bicarbonate. How many milli 4%
Name: Date: Section: Report Sheet: Determination of Molecular Weight Through Freezing Point Depression Analysis 30 Part A: Volume of Cyclohexane mL Mass of cyclohexane (d =0.7786 g/mL) 6.0 °C Freezing Point of cyclohexane 128 Part B: Molecular Weight of Naphthalene g/mol 0.23 Mass of Sample 1 Moles of Sample 1 Mass of Sample 2 0.18 Moles of Sample 2 Moles m (mol/kg solvent) T,('C) AT, Naphthalene 5.1 TRIAL 1 5.3 TRAIL 2 k, Cyclohexane CC/m) Part C: Unknown Number 0.21 0.19 Mass of Sample 1 Mass of Sample 2 Grams Unknown T,('C) AT 0.21 4.8 TRIAL 1 0.19 5.0 TRAIL 2 Moles UnknownTRIAL 1 (moles) TRIAL 2 (moles) TRIAL 1 (g/mol)TRIAL 2 (g/mol) Molecular Weight Unknown (g/mol) AVERAGE MOLECULAR WEIGHT OF UNKNOWN
A sample of 14000 ppm iron is Strong Acid has to be diluted between 95 and 180 ppm. The method chosen was to dilute in three dilutions of 100 mL each. The first dilution is a 1/5, the second dilution is a 1/6 and the third dilution is a 1/3. Determine how much of each component goes in each tube. Determine the concentration of each tube. Are we within the proper range?
Materials Needed solid I2 solid CUSO4-5H20 food dye solid (NH4)2SO4 heavy metals waste container halogenated waste container non-halogenated waste container semi-micro test tubes and rack regular test tubes and rack squash pipettes acetone cyclohexane propan-2-ol Method Part A: Solubility of ionic and molecular solids 1. Place a small amount (about the size of 1 grain of rice, see picture) of copper sulfate into each of three DRY semi-micro test tubes. Add 20 drops of water to the first test tube and gently flick the test tube with your finger to ensure mixing. 2. Repeat step 1 using acetone in place of water as the solvent in the second test tube. 3. Repeat step 2 replacing acetone with cyclohexane in the third test tube. Hold the test tubes against a white background to compare the solubility of copper sulfate in the three solvents and record your results. Discard these mixtures into the heavy metals waste container in the fume cupboard. Once these test tubes have been emptied you…
How to prepare 100 mL of 10% AlCl3
A student prepares a 0.71 Maqueous solution of trimethylacetic acid (C,H,CO,H). Calculate the fraction of trimethylacetic acid that is in the dissociated form in his solution. Express your answer as a percentage. You will probably find some useful data in the ALEKS Data resource. Round your answer to 2 significant digits. Oxto ?