You are on an elevator fixed to a wall that can move up and down freely while you pull with a force of 150 N on a massless rope (the orange line in the diagram below) with length L. This rope is connected to one end of a beam with the same length, L, and mass m=20 kg. The left end of the beam is in contact with the same wall the elevator is on and the coefficient of static friction =0.2 between the beam and the wall. See diagram below for a representation of the situation and note that free fall acceleration points directly downward L Part A) Label all the forces acting on the beam and discuss the direction of any torques exerted on the beam about the contact point between the beam and the wall Part B) What is the maximum angle the beam can subtend with respect to the horizontal _m such that it will just begin to slip? Potentially useful trig identities are sin(2x)=2sin(x)cos, sin(180-x)=sin(x), sin(90+x)=cos(x)

You are on an elevator fixed to a wall that can move up and down freely while you pull with a force of 150 N on a massless rope (the orange line in the diagram below) with length L. This rope is connected to one end of a beam with the same length, L, and mass m=20 kg. The left end of the beam is in contact with the same wall the elevator is on and the coefficient of static friction =0.2 between the beam and the wall. See diagram below for a representation of the situation and note that free fall acceleration points directly downward L Part A) Label all the forces acting on the beam and discuss the direction of any torques exerted on the beam about the contact point between the beam and the wall Part B) What is the maximum angle the beam can subtend with respect to the horizontal _m such that it will just begin to slip? Potentially useful trig identities are sin(2x)=2sin(x)cos, sin(180-x)=sin(x), sin(90+x)=cos(x)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.48P

See similar textbooks

Similar questions

5 non-concurrent forces are acting on two rings connected by a line that resulted in equilibrium. can you help me solve this equilibrium of forces question using the polygon method? the pieces of string are tied to a massless rings. the forces acting on the ring are in gram-force. thank you.
A mass of 300g hangs in a spring with a spring stiffness of 40 N/m (same situation as in Exercise 4.6). The mass is connected to the spring with a weightless cord, the rigidity of the cord can be considered infinite, ie it is so large that it does not affect the rigidity of the system. We start with a situation where the spring is not loaded and the weight is placed at the end of the spring. So the weight is ground free so that it falls from a height equal to the length of the string before it starts to act on the spring. 0 cm, 6.0 cm, 12 cm, 24 cm. That is, for situations when the length of the cord is 0 cm, 6.0 cm, 12 cm and 24 cm.
Q2: A particle is thrown at an angle of 30° with velocity of 36 kmph calculate its time of flight and horizontal range. Q3: A wire 10m long of cross section area 1.22 cm? elongates by 1.5 cm when 4.5 kg is suspended from it find: 1. Stress 2. Strain 3. Youngs modulus of the wire
You have been selected as a potential intern in a construction company in Aqaba, Jordan. For evaluation purposes, you were asked to answer the following question. Two wooden boxes are moving on an inclined surface as shown in Figure 2. Wooden Box A Non- Frictional Surface Non- Frictional Surface 60 Figure 2: Wooden Baxes Answer the following questions using the D'Alembert's principle. Note that the mass of box A is M1 and the mass of box B is M2. Wooden Box
You have been selected as a potential intern in a construction company in Aqaba, Jordan. For evaluation purposes, you were asked to answer the following question. Two wooden boxes are moving on an inclined surface as shown in Figure 2. Wooden Воx A Non- Frictional Surface Non- Frictional Surface 60 Figure 2: Wooden Boxes Answer the following questions using the D'Alembert's principle. Note that the mass of box A is M1 and the mass of box B is M2. 1. Find the tension in the rope, in terms of M1 and M2. 2. Calculate the acceleration of the wooden boxes, in terms of M1 and M2. Wooden Вох
A computer is protected against impact by foam packaging (spring stiffness, k = 100 N/cm; mass, m = 11 kg, including packaging). The maximum acceleration that the computer can withstand on impact with a hard surface is 4g. At the maximum acceptable impact acceleration, how much does the packaging compress upon impact? Give the answer in cm. What is the maximum height, h, in cm that the case can fall from without damaging the computer?
Please answer the following question A cigarettes dispenser requires a south African five-rand (R5) coin with a mass of 9.5 g to dispense one cigarette with a mass of 0.2 g. The design of such a cigarette dispenser is based on a helical spring, of negligible mass, which is found to extend 0.1 mm under a mass of 0.2 g. The spring can support a total mass of a coin. As the customer place money on the dispenser, the spring and coin system displace vertically through 4 mm and release. 1.1. Provide a schematic representation of the mass and spring system. 1.2. Calculate the frequency of natural vibration of the dispenser. 1.3. Determine the velocity of the coin when it is 2 mm below its resting position.
A long, thin, wire of uniform cross-section has Young's Modulus Y and mass density D. When laid horizontally on a bench its unstretched length is L. One end is attached to a fixed point and the rest of the wire is allowed to hang freely and vertically in the earth's gravitational field. Find the extension of the lowest end of the wire (i.e., the wire's length additional to L) due to gravitational force. The acceleration due to gravity is g.
During a bicep curl on a bicep curl machine, I'm curling a weight stack of 100 pounds (single arm...I'm jacked like that). At this very moment, the weight stack has a moment arm of 0.12m, my elbow has an angle of 63deg, my muscle force vector has an angle of 23deg, and it attaches 3cm below my elbow joint on my radius. How much force must my bicep create right at this moment to hold the weight stack in place?
BY 1.20 cm 7. QIC A simple pendulum consists of a small object of mass 3.0 kg hanging at the end of a 2.0-m-long light string that is connected to a pivot point. (a) Calculate the magnitude of the torque (due to the force of gravity) about this pivot point when the string makes a 5.0° angle with the vertical. (b) Does the torque increase or decrease as the Figure P8.6 angle increases? Explain.
5. The mass of the elevator cage is m, It moves downward with constant velocity vo by wire rope. The stiffness coefficient of wire rope is k. The mass is negligible. If the elevator stops abruptly during operation, what is the maximum tension of the wire rope? k m ko m Vo
1.4 The locomotive of a train can exert a maximum pull of 300 kN. The locomotive has a mass of 85 000 kg and the train a mass of 420 000 kg. Consider that the train is running up on an incline of 1 in 300 and the resistances to motion is 5.54 x 10-5 kN/kg Model the problem by drawing a free body diagram which suits to apply De Alembert's principle and calculate the maximum possible acceleration of the train. Suppose the train is running on a horizontal track with the acceleration of 0.4 m s?. By using De Alembert's principle, calculate the pull produced by the locomotive engine to get this acceleration. Assume the resistance to motion remains same as previous.