You are given a before condition of the registers eax, ebx, edx and an instruction. Choose the correct after condition of eax, edx Before condition: EAX: 00 00 00 11 EBX: 00 00 00 OC EDX FF FF FF 03 Instruction: CWD idiv bx After condition: EAX: 00 00 00 51 EDX: FF FF FF 01 O EAX: 00 00 05 01 EDX: FF FF FF 03 EAX: 00 00 00 01 EDX: 00 00 00 05 O EAX: 00 00 00 01 EDX: FF FF 00 05

You are given a before condition of the registers eax, ebx, edx and an instruction. Choose the correct after condition of eax, edx Before condition: EAX: 00 00 00 11 EBX: 00 00 00 OC EDX FF FF FF 03 Instruction: CWD idiv bx After condition: EAX: 00 00 00 51 EDX: FF FF FF 01 O EAX: 00 00 05 01 EDX: FF FF FF 03 EAX: 00 00 00 01 EDX: 00 00 00 05 O EAX: 00 00 00 01 EDX: FF FF 00 05

Principles of Information Systems (MindTap Course List)

12th Edition

ISBN:9781285867168

Author:Ralph Stair, George Reynolds

Publisher:Ralph Stair, George Reynolds

Chapter3: Hardware: Input, Processing, Output, And Storage Devices

Section: Chapter Questions

Problem 3SAT: The time it takes to perform the fetch instruction and decode instruction steps is called the...

See similar textbooks

Similar questions

The time it takes to perform the fetch instruction and decode instruction steps is called the execution time. True or false?
(d) The table below shows the ALUcontrol signal of the datapath we discussed in class. Instruction Funct ALU Орсode ALUop ALU action operation field control Iw 00 load word XXXXXX add 0010 Sw 00 store word XXXXXX add 0010 beq 01 branch equal subtract 0110 XXXXXX R-type 10 add 100000 add 0010 R-type 10 subtract 100010 subtract 0110 R-type 10 AND 100100 AND 0000 R-type 10 OR 100101 OR 0001 R-type 10 set on less than 101010 set on less than 0111 You want to add the bne instruction into the datapath, which already includes the required hardware for the instruction. Write out the ALUop for bne and how you can determine whether the bne results in the branch to be taken.
Select an XOR instruction that will: a) XOR BH with AH and save the result in AH.b) XOR 99H with CL.c) XOR DX with DI and save the result in DX.d) XOR 1A23H with SP.e) XOR the data addressed by BX with DX and save the result in memory.f) XOR the data stored 30 words after the location addressed by BP with DI and save the result in DI.
You are given a before condition of ecx register and an instruction. Choose the correct after condition of ecx: Before condition of ECX: 0A 00 BF 7A Instruction: mov cx, 9 After condition of ECX: 0 OA 00 BF79 ) 09 00 00 OA O OA 00 BF 09 O OA 00 0009
Given a memory load instruction, "mov R0; [R1+1000]," please give the input that should be selectedat each multiplexer. You can write "none" for the multiplexers that are not used for this instruction.(a) MUX1:(b) MUX2:(c) MUX3:(d) MUX4:
BX=FFFF, after instruction INC BX is executed, CF ||
2. What will be the value in the destination register after each of the following instructions executes in sequence, given that CL, DX, and AL are initialized to 3, 1001111010111100, and 01010111 respectively? shr dx, 1 shr dx, cl rol dx, cl ror al, 1 rcr al, cl rcr dx, 1 sar dx, cl sar al, 1 rcl dx, cl rcl al, cl med Walted Bonde ; a. ; b. ; c. ; d. ; e. ; f. ; g. ; h. ; i. ; j.Da batean rioned how mrithoglA S.O.
Using the following data definitions: bytel BYTE byte2 BYTE word1 WORD word2 WORD 3 OFFh, 1, 2 14h OFFFFh, 1, 2 word3 SWORD 7FFFh, 8000h word4 SWORD 9000h dword1 DWORD 10h, 20h, 30h, 40h dArray DWORD 10 DUP (?) Write an instruction that moves the lower 8 bits of word2 into the AL register.
4. Which segment will be accessed for the instruction MOV [BX],AH.
Based on the diagram below, what is the result for register DX after executing the mnemonic opcode/operand instructions? MOV AX, 200h MOV BX, 100h MUL BX АХ BX DX AX CF OF 200h X 100h The resulted DX is 00A2. a. The resulted DX is 0002. The resulted DX is 0012. OC. The resulted DX is 0022. Od.
Question 36 It is an instruction that illustrates powers of two. A) RCR AL, 03H, with AL = 01H %3D B) RCL AL, 03H, with AL = 01H RCL AL, 03H, with AL = 10H Question 37 It is an instruction that needs to identify a positive or negative value of the register. A MOVZX AX,AL B) IDIV AX MUL AX Question 38 It is an instruction that illustrates the opposite of powers of two. A) RCL AL, 03H, with AL = 10H B) RCL AL, 03H, with AL = 01H RCR AL, 03H, with AL = 80H Question 39 It is an instruction to clear the register. A) XOR AX,AX B) CLC c) CLEAR
In the Allen-Bradley MOV instruction, constants such as 250, 400, 5.5, etc., can be entered into the source location of the MOV instruction rather than a memory address containing the value to be moved. True False